Technogym BIOSTRENGTH LINE - Page 9

BIOSTRENGTH LINE: Service & Maintenance manual - rev. 2.1
Page v
7.3.37. Disassembling the starter plate and fuses ........................................................................................7.125
7.4. LEG CURL .....................................................................................................................................................7.126
7.4.1. Disassembling the display ................................................................................................................7.126
7.4.2. Removing the electronic display boards...........................................................................................7.127
7.4.3. Removing the EPROM......................................................................................................................7.129
7.4.4. Disassembling the TLCBR chip ........................................................................................................7.130
7.4.5. Disassembling the main keyboard ....................................................................................................7.131
7.4.6. Disassembling the seat keyboard......................................................................................................7.132
7.4.7. Disassembling the plexiglas weight stack guard ..............................................................................7.133
7.4.8. Disassembling the weight stack pulleys............................................................................................7.134
7.4.9. Disassembling the weight stack cover ..............................................................................................7.135
7.4.10. Disassembling the additional weight................................................................................................7.137
7.4.11. Disassembling the encoder...............................................................................................................7.138
7.4.12. Disassembling the solenoid ..............................................................................................................7.139
7.4.13. Disassembling the selector brush .....................................................................................................7.140
7.4.14. Disassembling the zero sensor..........................................................................................................7.141
7.4.15. Disassembling the weight stack selection system..............................................................................7.142
7.4.16. Disassembling the weight stack selection chain ...............................................................................7.143
7.4.17. Disassembling the weight stack motor..............................................................................................7.144
7.4.18. Disassembling the cross stops ..........................................................................................................7.145
7.4.19. Disassembling the cross....................................................................................................................7.146
7.4.20. Disassembling the sinker ..................................................................................................................7.147
7.4.21. Disassembling the weight stack plates..............................................................................................7.148
7.4.22. Disassembling the bars.....................................................................................................................7.149
7.4.23. Disassembling the seat guard...........................................................................................................7.150
7.4.24. Disassembling the seat motor ...........................................................................................................7.151
7.4.25. Disassembling the electrical box ......................................................................................................7.153
7.4.26. Disassembling the electronic components of the electrical box .......................................................7.154
7.4.27. Disassembling the bell guard ...........................................................................................................7.156
7.4.28. Disassembling the weight stack frame guard ...................................................................................7.157
7.4.29. Disassembling the weight stack cable...............................................................................................7.158
7.4.30. Disassembling the bell......................................................................................................................7.159
7.4.31. Disassembling the primary shaft - secondary shaft chain ................................................................7.160
7.4.32. Disassembling the primary shaft ......................................................................................................7.161
7.4.33. Disassembling the secondary shaft...................................................................................................7.163
7.4.34. Disassembling the weight stack frame pulley ...................................................................................7.165
7.4.35. Disassembling the mat......................................................................................................................7.166
7.4.36. Disassembling the power entry.........................................................................................................7.167
7.4.37. Disassembling the starter plate and fuses ........................................................................................7.168
7.5. VERTICAL TRACTION.....................................................................................................................................7.169
7.5.1. Disassembling the display ................................................................................................................7.169
7.5.2. Removing the electronic display boards...........................................................................................7.170
7.5.3. Removing the EPROM......................................................................................................................7.172
7.5.4. Disassembling the TLCBR chip ........................................................................................................7.173
7.5.5. Disassembling the main keyboard ....................................................................................................7.174
7.5.6. Disassembling the seat keyboard......................................................................................................7.175
7.5.7. Removing the seat.............................................................................................................................7.176
7.5.8. Disassembling the front guard..........................................................................................................7.177
7.5.9. Disassembling the electrical box ......................................................................................................7.178
7.5.10. Disassembling the electronic components of the electrical box .......................................................7.179
7.5.11. Disassembling the upright guard......................................................................................................7.181
7.5.12. Disassembling the seat motor ...........................................................................................................7.182
7.5.13. Disassembling the prestart cable......................................................................................................7.183
7.5.14. Disassembling the rear guard...........................................................................................................7.185
7.5.15. Disassembling the solenoid ..............................................................................................................7.186
7.5.16. Disassembling the selector brush .....................................................................................................7.187
7.5.17. Disassembling the weight stack cable...............................................................................................7.188
7.5.18. Disassembling the pulleys.................................................................................................................7.189