Technogym BIOSTRENGTH LINE - Page 8

BIOSTRENGTH LINE: Service & Maintenance manual - rev. 2.1
Page iv
7.2.16. Disassembling the weight stack motor................................................................................................7.58
7.2.17. Disassembling the cross stops ............................................................................................................7.59
7.2.18. Disassembling the cross......................................................................................................................7.60
7.2.19. Disassembling the sinker ....................................................................................................................7.61
7.2.20. Disassembling the weight stack plates................................................................................................7.62
7.2.21. Disassembling the bars.......................................................................................................................7.63
7.2.22. Disassembling the seat guard.............................................................................................................7.64
7.2.23. Disassembling the electrical box ........................................................................................................7.65
7.2.24. Disassembling the electronic components of the electrical box .........................................................7.66
7.2.25. Disassembling the bell guard .............................................................................................................7.68
7.2.26. Disassembling the weight stack frame guard .....................................................................................7.69
7.2.27. Disassembling the weight stack cable.................................................................................................7.70
7.2.28. Disassembling the release lever cable................................................................................................7.71
7.2.29. Disassembling the bell........................................................................................................................7.73
7.2.30. Disassembling the primary shaft - secondary shaft chain ..................................................................7.74
7.2.31. Disassembling the primary shaft ........................................................................................................7.75
7.2.32. Disassembling the secondary shaft.....................................................................................................7.77
7.2.33. Disassembling the weight stack frame pulley .....................................................................................7.79
7.2.34. Disassembling the mat........................................................................................................................7.80
7.2.35. Disassembling the power entry...........................................................................................................7.81
7.2.36. Disassembling the starter plate and fuses ..........................................................................................7.82
7.3. LEG EXTENSION..............................................................................................................................................7.83
7.3.1. Disassembling the display ..................................................................................................................7.83
7.3.2. Removing the electronic display boards.............................................................................................7.84
7.3.3. Removing the EPROM........................................................................................................................7.86
7.3.4. Disassembling the TLCBR chip ..........................................................................................................7.87
7.3.5. Disassembling the main keyboard ......................................................................................................7.88
7.3.6. Disassembling the seat keyboard........................................................................................................7.89
7.3.7. Disassembling the Plexiglas weight stack guard................................................................................7.90
7.3.8. Disassembling the weight stack pulleys..............................................................................................7.91
7.3.9. Disassembling the weight stack cover ................................................................................................7.92
7.3.10. Disassembling the additional weight..................................................................................................7.94
7.3.11. Disassembling the encoder.................................................................................................................7.95
7.3.12. Disassembling the solenoid ................................................................................................................7.96
7.3.13. Disassembling the selector brush .......................................................................................................7.97
7.3.14. Disassembling the zero sensor............................................................................................................7.98
7.3.15. Disassembling the weight stack selection system................................................................................7.99
7.3.16. Disassembling the weight stack selection chain ...............................................................................7.100
7.3.17. Disassembling the weight stack motor..............................................................................................7.101
7.3.18. Disassembling the cross stops ..........................................................................................................7.102
7.3.19. Disassembling the cross....................................................................................................................7.103
7.3.20. Disassembling the sinker ..................................................................................................................7.104
7.3.21. Disassembling the weight stack plates..............................................................................................7.105
7.3.22. Disassembling the bars.....................................................................................................................7.106
7.3.23. Disassembling the seat guard...........................................................................................................7.107
7.3.24. Disassembling the seat motor ...........................................................................................................7.108
7.3.25. Disassembling the electrical box ......................................................................................................7.110
7.3.26. Disassembling the electronic components of the electrical box .......................................................7.111
7.3.27. Disassembling the bell guard ...........................................................................................................7.113
7.3.28. Disassembling the weight stack frame guard ...................................................................................7.114
7.3.29. Disassembling the weight stack cable...............................................................................................7.115
7.3.30. Disassembling the bell......................................................................................................................7.116
7.3.31. Disassembling the primary shaft - secondary shaft chain ................................................................7.117
7.3.32. Disassembling the primary shaft ......................................................................................................7.118
7.3.33. Disassembling the secondary shaft...................................................................................................7.120
7.3.34. Disassembling the weight stack frame pulley ...................................................................................7.122
7.3.35. Disassembling the mat......................................................................................................................7.123
7.3.36. Disassembling the power entry.........................................................................................................7.124