Toptech Systems MultiLoad II SCS User Manual

6
Firmware Version 3/4.31.37
5.2.6 Adaptive Digital Control Algorithm ..................................................................................................... 175
5.2.7 Two Stage Valves .............................................................................................................................. 175
5.2.8 Analog Valves .................................................................................................................................... 176
5.3 Sequential Blending (Excluding SMP) ............................................................................................... 176
5.3.1 Sequential Blending Configuration .................................................................................................... 177
5.4 Ratio Blending (Excluding SMP) ........................................................................................................ 180
5.4.1 Ratio Blending Configuration ............................................................................................................. 181
5.5 Side-Stream Blending (Excluding SMP) ............................................................................................ 184
5.5.1 Simple Side-Stream Blender Configuration ....................................................................................... 185
5.6 Hybrid Blending (Excluding SMP) ..................................................................................................... 186
5.6.1 Multiple Side-Streams ........................................................................................................................ 186
5.6.2 Sequential Blending with Side-Stream .............................................................................................. 187
5.6.3 Ratio Blending with Side-Stream ....................................................................................................... 188
5.7 Proving Side-Stream Meters (Excluding SMP) ................................................................................. 191
5.8 Line Flush (Excluding SMP) ............................................................................................................... 191
5.9 Ratio Blending Considerations (Excluding SMP) ............................................................................ 194
5.10 Calibration Using Meter Factor Linearization ................................................................................... 195
5.10.1 Single Meter Factor ....................................................................................................................... 197
5.10.2 Rules for Meter Factors ................................................................................................................. 197
CHAPTER 6 ADDITIVE CONTROL ............................................................................................................... 198
6.1 Overview ............................................................................................................................................... 198
6.2 Piston Injector Cycles ......................................................................................................................... 198
6.3 Additive Port Assignment ................................................................................................................... 199
6.3.1 Additive Output Port and Input Port Assignments ............................................................................. 199
6.4 Additive Units ....................................................................................................................................... 200
6.5 Additive Control Methods ................................................................................................................... 200
6.5.1 Method 1 – Piston Only ..................................................................................................................... 200
6.5.2 Configuring a Piston Only Additive .................................................................................................... 201
6.5.3 Method 2 – Piston with Input (Feedback Switch) .............................................................................. 201
6.5.4 Configuring a Piston with Input Additive ............................................................................................ 202
6.5.5 Method 3 – Pulser Input ..................................................................................................................... 203
6.5.6 Configuring a Pulser Input Additive ................................................................................................... 203
6.5.7 Method 4 – Analog Additive ............................................................................................................... 204
6.5.8 Configuring a Analog Additive ........................................................................................................... 204
6.5.9 Method 5 – Common Meter with Multiple Additives .......................................................................... 204
6.5.10 Additive Block Valves Only ............................................................................................................ 206
6.5.11 Configuring a Common Meter with Multiple Additives ................................................................... 207
6.6 General Additive Setup ....................................................................................................................... 210
6.7 Additive Calibration ............................................................................................................................. 217
6.7.1 Additive Cal. Function ........................................................................................................................ 217
6.7.2 Automatic Calibration Function .......................................................................................................... 218
6.7.3 Piston Type Additive Calibration ........................................................................................................ 222
6.8 Calculate Additive Vol/Inject .............................................................................................................. 223
6.9 Remote Additive Calibration .............................................................................................................. 225
6.10 Additive Status Screen........................................................................................................................ 230
6.11 Additive Flush Features ...................................................................................................................... 231
6.11.1 Basic Flush Features ..................................................................................................................... 231
6.11.2 Techniques for Flushing Dye ......................................................................................................... 233

Toptech Systems MultiLoad II SCS Specifications

General

Brand	Toptech Systems
Model	MultiLoad II SCS
Category	Control Unit
Language	English