Uninet IColor 250 - User Manual

Questions and Answers

A
Andrea ReyesAug 5, 2025
How to fix horizontal offset on Uninet Printer?
- R
  rgreenAug 5, 2025
  If your Uninet Printer's image is printing horizontally offset, resulting in white space on one side of the label, it could be due to the Left Margin Offset. To correct this, increase the number if you see white space on the right side and overlap on the opposite side. Decrease the number if you see white space on the left side and overlap on the opposite side. Also, ensure that the page size is large enough to cover the label by adjusting the printer preferences.
M
Michelle SmithAug 10, 2025
Why is my Uninet IColor 250 image vertically offset?
- C
  Curtis SchwartzAug 10, 2025
  If you notice a vertical offset in the image printed by your Uninet Printer, resulting in white space at the top or bottom of the label, several factors could be responsible. First, adjust the TOF Offset: increase this setting to move the image down or decrease it to move the image up. Ensure your label stock is compatible by testing with approved label stock from UNINET. Check that the label gap distance is correct. Also, verify that the page size setting matches your label stock size and that the portrait/landscape setting is correctly configured. Finally, if using circular or non-rectangular die-cut labels, refer to Section 2B for instructions on sensor position.
L
Luis ClarkAug 16, 2025
What to do if my Uninet Printer has poor print quality?
- J
  Joseph DiazAug 16, 2025
  If you are experiencing poor print quality with your Uninet Printer, it could be due to low ink levels (below 10%). In this case, replace the cartridge. You can also try cleaning the cartridge using the clean function in the UNINET IColor PrintHub.
M
Mia AliAug 23, 2025
How to clean ink accumulation on Uninet IColor 250 Printer wipers?
- D
  Debbie WatsonAug 23, 2025
  To address ink accumulation on the wipers of your Uninet Printer, check the wipers and clean them using rubbing alcohol and a cotton tip cleaner.
B
boltongregoryAug 29, 2025
How to adjust cutter offsets on Uninet IColor 250?
- S
  scottfergusonAug 29, 2025
  To adjust cutter offsets on your Uninet IColor Printer, open the UNINET IColor Print Hub, go to the Printer Settings tab, and click on the Advanced Settings button. Adjust the cutter offsets according to the diagram provided.

Summary

Getting Started

Choosing a Good Location

Proper placement ensures optimal printer performance and longevity.

Unpacking and Inspection

Verify all included accessories and check for shipping damage.

Installing the Roll Holders

Guide to correctly attach label roll holders for media feeding.

Identifying the Parts

Familiarization with the printer's external components and controls.

Media, Cartridges, and Knives

Label and Roll Specifications

Details on compatible media types, dimensions, and smart chip requirements.

Installing Digital Die-Cutting Label Stock

Step-by-step guide for loading UNINET digital die-cut media.

Installing Pre-Die-Cut Label Stock

Instructions for loading standard pre-die-cut label rolls.

Replacing the Digital Die-Cutting Knife holder

Procedure for removing and installing the die-cutting knife holder.

Replacing the Cutting Knife

Steps for replacing a worn or damaged cutting knife.

Replacing Ink Cartridges

Instructions on how to safely remove and install ink cartridges.

Adjusting the Gap Sensor Position

How to set the sensor for non-standard label stock.

UNINET IColor PrintHub

XY Cutting Settings- Cut Offsets, Knife Pressure, and Stretch Factor

Configure cut parameters like offsets, pressure, and stretch for precise cutting.

Set the Gap Sensor Mode

Select the sensor mode for different label types (Die-Cut, Reflective, Continuous).

Set the Present;Cut Mode

Define how the printer presents labels after printing or cutting.

Adjusting Print Alignment

Fine-tune print positioning for accurate placement on various label types.

UNINET IColor PrintHub Settings

Configure general application settings like language and support.

UNINET IColor PrintHub Printer Settings

Access printer-specific settings and advanced options.

Printing and Cutting with IColor CustomCUT Software on PC and Mac

Overview IColor CustomCUT

Introduction to the software's interface and core features.

IColor CustomCUT Software Activation

Steps to activate the IColor CustomCUT software using an activation code.

Tutorial: Setup Print and Cut (Vector File Cut)

Guide to creating print and cut jobs using vector files.

Tutorial: Setup Print and Cut (Contour Cut)

Guide to creating print and cut jobs using image tracing.

Setup Multiple Identical Cuts (Duplicate and Array)

Duplicate images and cut lines for efficient multi-label production.

Vector File Specifications for Designer

Guidelines for preparing vector files for optimal import and cutting.

Printing Only to Pre-Die-Cut Labels

Using BarTender for Pre-Die-Cut Printing

Step-by-step guide for setting up labels in BarTender software.

Printing From Other Programs

Tips for printing from applications other than BarTender.

Creating a Full Bleed Print

Adjust settings for labels with no white margins.

Printer Driver Settings

Configure paper size, orientation, print quality, and color matching.

Printing from a Mac

Print Utility Setting (IColor 250 Config Utility)

Accessing and using the printer configuration utility on macOS.

Adjusting Print Alignment; Label Offsets (Pre-Die-Cut Only)

Fine-tuning print alignment and label offsets via the utility.

Set the Stock Sensor Mode (Pre-Die-Cut Only)

Selecting the appropriate sensor mode for different stock types.

XY Cutter Offsets (Digital Die-Cut Stock Only)

Adjusting horizontal and vertical offsets for the cutting mechanism.

Creating a Custom Size - Mac

How to define custom page sizes for printing on Mac.

Printer Driver Settings

Accessing and configuring printer driver settings on Mac.

Troubleshooting

Solving Pre-Die-Cut Print Alignment Problems

Diagnosing and fixing issues with print alignment on pre-die-cut labels.

Cleaning the Cartridge - Poor Print Quality

Steps to clean ink cartridges to resolve poor print quality.

Solving Cut Alignment Offset Problems

Resolving problems related to misaligned cut paths.

Maintenance

Routine maintenance procedures for the printer.

Technical Support

Information on how to contact technical support for assistance.

Technical Specifications

Uninet IColor 250 Specifications

General

Print Technology	LED
Max Print Resolution	1200 x 600 dpi
Connectivity	USB 2.0
Operating Systems Supported	Windows, Mac OS
Input Capacity	250 sheets
Maximum Print Width	8.5 inches
Media Types Supported	Plain Paper, Card Stock, Envelopes, Labels, Transparencies
Media Sizes	Letter, Legal, A4, A5, B5, Executive