VI.BE.MAC.S.p.A.
pag.2
INDEX page
GENERAL MACHINE SPECIFICATIONS.........................................................................................................................4
1.1.SUPPLY VOLTAGE....................................................................................................................................................4
1.2.COMPRESSED AIR CONSUMPTION AND PRESSURE.......................................................................................4
1.3.DIMENSIONS AND WEIGHT ...................................................................................................................................4
1. CONDITIONS OF USE .................................................................................................................................................5
2.1.FORM OF GUARANTEE............................................................................................................................................5
2. WORK STATION ..........................................................................................................................................................6
3. MACHINE START-UP..................................................................................................................................................7
4. STOPPING THE MACHINE.........................................................................................................................................7
5. CALLING UP A PROGRAMME..................................................................................................................................7
6. WRITING A PROGRAMME .......................................................................................................................................8
7. CANCELLING A PROGRAMME................................................................................................................................8
8. COPYING PROGRAMMES..........................................................................................................................................9
9. SETTING BOBBIN AND PRODUCTION COUNTERS..........................................................................................10
9.1.RESETTING BOBBIN COUNTER ..........................................................................................................................10
9.2.RESETTING PRODUCTION COUNTER (start of production) .............................................................................10
10. CHANGING THE FORM ON THE EQUIPMENT BETWEEN TWO DIFFERENT SEWINGS......................11
10.1.FROM ONE DESIGN TO ANOTHER OF DIFFERENT SHAPE........................................................................11
10.2.FROM ONE LABEL TO ANOTHER OF DIFFERENT SHAPE..........................................................................11
11. CHANGING THE EQUIPMENT............................................................................................................................12
11.1.FROM THE DESIGN TO THE LABEL .................................................................................................................12
12. OPERATING SYSTEM...........................................................................................................................................14
12.1.OPERATING SYSTEM SELECTION....................................................................................................................14
13. LIST OF ERRORS AND MESSAGES MITSUBISHI TYPE "B" ........................................................................15
13.1.LIST OF ERRORS (E - xx)......................................................................................................................................15
13.2.LIST OF MESSAGES (M - xx) ...............................................................................................................................16
14. ELECTRICAL CONNECTION...............................................................................................................................18
14.1.INPUTS .....................................................................................................................................................................18
14.2.OUTPUTS .................................................................................................................................................................19
15. SOLENOID VALVES..............................................................................................................................................20
16. CONTROL CIRCUIT...............................................................................................................................................21
16.1 ELECTRIC LIMIT STOPS for LOADER...............................................................................................................21
16.2.FLOW REGULATORS............................................................................................................................................21
16.3.LOADING CYLINDER EXPANSIONS.................................................................................................................21
17. ORIGINAL POINT SENSORS ...............................................................................................................................22
18. PNEUMATIC SYSTEM ..........................................................................................................................................22
19. LIFTING THE SEWING HEAD .............................................................................................................................23
20. OPERATING SOFTWARE PARAMETERS.........................................................................................................24
20.1.VARYING TIMER SETTINGS WITH AUTOMATIC CYCLE PRMB = 1........................................................24
20.2.VARYING TIMER SETTINGS WITH AUTOMATIC CYCLE PRMB = 2........................................................25
20.3.INPUTS / OUTPUTS TEST.....................................................................................................................................26
20.4.MATERIAL CARRIAGE PARAMETER CONTROL – TENSION RELEASE TIME DURING CUT
CYCLE ..............................................................................................................................................................................29
20.5.CONTROL OF SET SPEEDS (FEED and SEWING) AND SLOW START FUNCTION..................................30
21. PROGRAMMING ....................................................................................................................................................32
21.1.GENERAL SPECIFICATIONS...............................................................................................................................32
21.1.1.MEMORY ..............................................................................................................................................................32
21.1.2.STITCH LENGTH.................................................................................................................................................32
21.1.3.SEWING SPEED...................................................................................................................................................32
21.1.4.CODES ...................................................................................................................................................................32
21.1.5.METHOD OF PROGRAMMING ........................................................................................................................32
21.2.PROGRAMMING AN EMBROIDERY .................................................................................................................33
21.3.RE-PROGRAMMING THE SECOND SEAM IN AN EMBROIDERY ..............................................................35
21.4.PROGRAMMING A LABEL ..................................................................................................................................37
22. MODIFICATIONS TO THE PROGRAMME ....................................................................................................... 39
22.1.GENERAL SPECIFICATIONS...............................................................................................................................39
22.1.1.MEMORY ..............................................................................................................................................................40
22.1.2.STITCH LENGTH.................................................................................................................................................40
22.2.MOVING THE ENTIRE PROGRAMME...............................................................................................................41
22.3.MODIFYING AN ANGLE INSERTED IN THE PROGRAMME........................................................................42
22.4.MODIFYING A CURVE INSERTED IN THE PROGRAMME...........................................................................44
22.5.MODIFYING THE SEWING SPEED (n° of stitches) ..........................................................................................46
22.6.ADDING CODES.....................................................................................................................................................48
22.7.REMOVING CODES...............................................................................................................................................49
To Next Page
Loading...