Need help?Do you have a question about the Weidmüller 610 and is the answer not in the manual?
General| Brand | Weidmüller |
|---|---|
| Model | 610 |
| Category | Measuring Instruments |
| Language | English |
Describes pictograms used in the manual for warnings and notes.
General instructions and warnings for product use and safety.
Procedures for checking the device upon arrival for damage or completeness.
Lists all items included with the Energy Meter 610/610-PB.
Defines the intended application and purpose of the device.
Details technical specifications and key capabilities of the device.
Explains the principle behind the device's electrical measurements.
Describes how users interact with the device via buttons and interfaces.
Overview of the accompanying software for configuration and analysis.
Illustrates different ways to connect the device to a PC.
Specifies suitable environments for device installation.
Details correct orientation and clearances for installation.
Step-by-step guide for physically installing the device.
Instructions for connecting the device's power supply.
Explains how voltage measurements are performed in different systems.
Lists supported mains voltage ranges for measurements.
Details the specifications of voltage input terminals.
Requirements for safe voltage connection.
Requirements for safe current connection.
Illustrates various voltage measurement wiring configurations.
Explains how current is measured using transformers.
Safety precautions for current transformer wiring.
Importance of earthing CT secondary windings.
Warnings related to open-circuit current transformers.
Illustrates various current measurement wiring configurations.
How to measure current using two transformers.
Details on connecting and using the RS485 interface.
Information on bus termination for RS485.
Explains the RS485 network topology.
Instructions for connecting via USB.
Overview of Profibus connectivity.
How to wire the Profibus bus.
Connecting and configuring digital outputs.
Connecting and configuring digital inputs.
Specific instructions for S0 pulse input.
LED indicators for digital input status.
LED indicators for digital output status.
LED indicators for Profibus communication status.
How to navigate and view measured values on the display.
How to enter and navigate programming menus.
Overview of storable parameters and measured values.
Describes the function of each button.
Powering the device for configuration.
Setting current and voltage transformer ratios.
Setting primary and secondary current transformer ratios.
Setting primary and secondary voltage transformer ratios.
General procedure for changing device parameters.
Setting the unique address for network devices.
Configuring the communication speed for RS485.
Setting averaging times for measured values.
How minimum and maximum values are recorded.
Setting or auto-detecting mains frequency.
Types of energy measurement available.
Measuring and displaying harmonic distortion.
Calculation and display of THD values.
Automatic cycling through displayed values.
Configuring how measured values are displayed.
Setting a password to protect configuration settings.
Resetting energy measurement data.
Displaying phase sequence information.
Adjusting display brightness settings.
Adjusting screen contrast.
Recording operating hours and comparator times.
Function of the operating hours meter.
Displaying the device's serial number.
Feature for tracking maximum mean values over time.
Information on preconfigured data recording.
Connecting power for commissioning.
Connecting voltage inputs for measurement.
Connecting current inputs for measurement.
Verifying correct phase conductor connections.
Verifying accuracy of power readings.
Verifying overall measurement accuracy.
Validating power values per phase.
Validating total power values.
Using Modbus RTU protocol for data access.
List of supported Modbus function codes.
Steps to install the necessary USB driver.
Verifying the USB connection and driver status.
How Profibus profiles enable data exchange.
Controlling outputs and tariffs using Profibus.
Disabling meters or tariffs via Profibus.
Retrieving data using Profibus profiles.
Explains Profibus system variables and formats.
Describes data formats within Profibus profiles.
Details of standard Profibus profiles.
Functionality and configuration of digital outputs.
Using digital outputs for pulse generation.
Setting the duration of output pulses.
Setting the energy value per pulse.
Calculation method for pulse value.
Setting up comparator groups and thresholds.
Procedures for device repair and calibration.
Guidelines for environmentally responsible device disposal.
How to contact technical support.
Information on factory calibration.
Process for updating the device's firmware.
Information about the device's internal battery.
How battery status is indicated.
Step-by-step guide for battery replacement.
General display of error codes and symbols.
Classification and handling of warning messages.
Classification and handling of serious error messages.
Common internal error codes and causes.
Specific error codes related to clock and battery.
Explains overrange indicators and limits.
Detailed description of parameter overrange coding.
Troubleshooting guide for common issues.
Basic specifications like weight and dimensions.
Conditions for shipping and storing the device.
Environmental requirements for normal use.
Electrical power requirements and ratings.
Specifications for connecting power terminals.
Technical details for voltage measurement.
Specifications for digital input terminals.
Technical data for RS485 and USB.
Technical details for current measurement inputs.
Table listing function parameters, ranges, and accuracy.
Comprehensive list of configurable parameters and Modbus addresses.
Detailed list of Modbus addresses for measured values.
Explanation of data type formats used.
Information on data persistence.
Visual representations of the device's physical size.
Displays for various voltage readings.
Displays for various current readings.
Displays for active, reactive, and apparent power.
Displays for THD values.
Displays for harmonic distortion values.
Displays for total energy consumption.
Displays for reactive energy consumption.
Displays for power factor and frequency.
Displays for comparator status and running times.
Displays for higher-order harmonics.
Displays for L4 current and related values.
Step-by-step guide for CT configuration.
How to navigate and view different measured values.
Explanation of button operations.
To Next Page
