178
MOTIF XS6/MOTIF XS7/MOTIF XS8
Now collecting the information of the
network...
This message appears while obtaining the network information.
Now executing Factory set... Indicates this synthesizer is restoring the factory-programmed settings.
.dedaolgniebsielfiatahtsetacidnI...gnidaolwoN
Now receiving MIDI bulk data... Indicates this synthesizer is receiving MIDI bulk data.
.devasgniebsielfiatahtsetacidnI...gnivaswoN
Now scanning autoload file. Scanning for the files specified for Auto Load.
Now transmitting MIDI bulk data... Indicates this synthesizer is transmitting MIDI bulk data.
Overwrite.
Are you sure?
A save operation will overwrite data on the external storage device as destination, and this message
confirms whether it is OK to continue or not. Press [INC/YES] or [DEC/NO] as required.
,drows
sapderetsigerydaerlaehthctamtonseodtupniuoydrowssapehT.dilavnisidrowssaP
Password is too short. The password you input to “New Password” is too short. Input at least five characters as a password.
Password is unspecified. This message appears when setting the File Server Switch parameter to “ON” though a password has
not been registered.
Pattern length mismatch. A Pattern Job will result in the length of a Pattern being greater than 256 measures.
Phrase length mismatch. A Pattern Job will result in the length of a phrase being greater than 256 measures.
Phrase limit exceeded. The maximum number of Phrases (256) has been exceeded when recording, executing a Pattern Job,
or editing.
Please keep power on. The data is being written to Flash ROM. Never attempt to turn off the power while data is being written to
Flash ROM. Turning the power off while this message is shown results in loss of all user data and may
cause the system to freeze (due to corruption of data in the Flash ROM). This may also result in the
MOTIF XS being unable to properly start up the next time the power is turned on.
Please select User Voice. This message appears when entering the File mode from the Performance mode and selecting a Part to
which a preset Voice is assigned in the Waveform Load operation.
Please stop sequencer. The operation you have attempted to execute cannot be done during Song/Pattern playback.
Sample frequency is too low. The sampling frequency is too low and the Frequency Convert Job cannot be executed.
.detucexeebtonna
cboJhctertSemiTehtdnaegralootsieziselpmaSehT.gnolootsielpmaS
.detucexeebtonnacboJtrevnoCycneuqerFehtdn
atrohsootsihtgnelelpmaSehT.trohsootsielpmaS
Sample memory full. The Sample memory is full and further Sampling operations, Jobs, or load operations cannot be
executed.
gnilpmaSehtgnitucexenehwdedeecxeneebsahsecioVelpmaSforeb
munllarevomumixamehTllufeciovelpmaS
related operations including the Job and Load.
.snottub]5FS[–]1FS[ehtfoenootderotsneebsahenecSgnoSehT.derotsenec
S
Sequence memory full. The internal memory for Sequence data is full, preventing any further operation (such as recording,
editing, Job execution, MIDI reception/transmission, or loading from the external storage device). Try
again after erasing unwanted Song, Pattern, or User Phrase data.
System memory crashed. Writing data to Flash ROM has failed.
The edited sequence data will be
discarded.
Are you sure?
Indicates that the operation will delete the currently edited Song or Pattern.
This Performance uses user Voices. The Performance you have loaded includes User Voice data. Check whether the Voice you saved exists
at the appropriate User voice bank.
Too many fixed notes. When converting the song or pattern data to the Arpeggio data, the amount of different notes in the data
to be converted has exceeded sixteen.
T .dedeecxeneebsah)2918(selpmasforebmunllarevomumixamehT.selpmaSynamoo
Unsupported disk or memory. An external USB storage device which this synthesizer does not support is connected to the USB TO
DEVICE terminal.
USB connection terminated.
Press any button.
A break in the connection with the USB storage device has occurred because of an abnormal electric
current. Disconnect the USB storage device from the USB TO DEVICE connector, then press any of the
panel buttons.
Utility/Sequencer Setup settings stored. The settings in the Utility mode have been stored.
W detalergnilpm
aSehtgnitucexenehwdedeecxeneebsahsmrofevaWforebmunllarevomumixamehTllufmrofeva
operations including Jobs and Load.
When the checkbox is “on,” all user
data is initialized the next time the
power is turned on.
(Self-explanatory)
LCD Indication Description
To Next Page
Loading...
Need help?
General
