Axion 40 Series - Default Chapter; Table of Contents

TABLE OF CONTENTS
SECTION 1
1. INTRODUCTION....................................................................................................................................... 2
1.1. GENERAL......................................................................................................................................... 2
1.2. FEATURES....................................................................................................................................... 2
1.2.1. CONTROL CONSOLE / OSCP..............................................................................................2
1.2.2. DESTINATION SIGN..............................................................................................................2
1.2.2.1. THE 8.5-INCH CHARACTER SIGN..........................................................................2
1.2.2.2. THE 8-INCH CHARACTER SIGN.............................................................................2
1.2.2.3. THE 6-INCH CHARACTER SIGN.............................................................................3
1.2.2.4. THE 4.5-INCH CHARACTER SIGN..........................................................................3
1.2.2.5. THE 3.2-INCH CHARACTER SIGN..........................................................................3
1.3. DATABASE TRANSFER..................................................................................................................3
1.3.1. DATA TRANSIT SOFTWARE................................................................................................3
1.3.2. TRANSFER UNIT (TU)...........................................................................................................3
1.4. DISTRESS SIGNAL.......................................................................................................................... 4
1.5. “YIELD” SIGNAL............................................................................................................................... 4
SECTION 2
2. INSTALLATION......................................................................................................................................... 6
2.1. MECHANICAL INSTALLATION........................................................................................................6
2.1.1. CONTROL CONSOLE / OSCP INSTALLATION....................................................................6
2.1.2. INTERIOR SIGNS INSTALLATION........................................................................................6
2.1.3. OUTSIDE REAR SIGN INSTALLATION................................................................................7
2.1.4. DISTRESS SIGNAL SWITCH INSTALLATION......................................................................7
2.1.5. YIELD SWITCH INSTALLATION............................................................................................7
2.2. ELECTRICAL INTERCONNECTION................................................................................................7
2.2.1. MAIN POWER CABLE...........................................................................................................8
2.2.1.1. BATT+ WIRE.............................................................................................................9
2.2.1.2. GND WIRE................................................................................................................9
2.2.1.3. IGN WIRE..................................................................................................................9
2.2.1.4. ACC WIRE................................................................................................................. 9
2.2.2. CONTROL CONSOLE POWER CABLE................................................................................9
2.2.3. OSCP POWER CABLE........................................................................................................12
2.2.4. OSCP COMMUNICATION CABLE.......................................................................................14
2.2.5. THE 802.11 b/g Wi-Fi MODULE ANTENNA CABLE FOR CONTROL CONSOLE..............15
2.2.6. THE 802.11 b/g/n Wi-Fi MODULE ANTENNA CABLE FOR OSCP.....................................15
2.2.7. CURB SIDE SIGN POWER CABLE.....................................................................................16
2.2.8. ROUTE SIDE SIGN POWER CABLE...................................................................................17
2.2.9. REAR SIGN POWER CABLE..............................................................................................18
2.2.10. KEY NUMBER SIGN POWER CABLE.................................................................................18
2.3. INSTALLATION FINAL CHECKS...................................................................................................19
2.4. CONTROL CONSOLE POST-INSTALLATION FUNCTIONALITY TEST.......................................19
2.4.1. STEP 1 : EDSS STARTUP...................................................................................................19
2.4.2. STEP 2: CONTROL CONSOLE CONFIGURATION............................................................20
2.4.3. STEP 3: DISTRESS (EMERGENCY) SWITCH TEST (IF INSTALLED)...............................20
2.4.4. STEP 4: YIELD SWITCH TEST (IF INSTALLED).................................................................20
2.4.5. STEP 5: OFF DELAY FUNCTIONALITY TEST....................................................................20
2.4.6. STEP 6: PHOTOSENSOR LIGHT INTENSITY CONTROL..................................................20
2.5. OSCP POST-INSTALLATION FUNCTIONALITY TEST.................................................................21
2.5.1. STEP 1: SIGNS SYSTEM STARTUP...................................................................................21
2.5.2. STEP 2: DISTRESS (EMERGENCY) SWITCH TEST (IF INSTALLED)...............................22
2.5.3. STEP 3: YIELD SWITCH TEST (IF INSTALLED).................................................................22
2.5.4. STEP 4: PHOTOSENSOR LIGHT INTENSITY CONTROL..................................................22
2.5.5. STEP 5: OFF DELAY FUNCTIONALITY TEST....................................................................22
SECTION 3
3. MAINTENANCE....................................................................................................................................... 24
3.1. TEST EQUIPMENT........................................................................................................................ 24
3.2. CLEANING..................................................................................................................................... 24
v