EXTERIOR & INTERIOR CARE — 3
76
20 08 CONTESSA
Dents:
Small dents may be repaired by using steam.
To raise a small dent, place a damp cloth over
the area and hold a medium-hot iron on it. The
steam causes the wood bers to swell back into
place. It may be necessary to repeat this process
until the dented area is level with the surface.
Allow the area to dry.
Restoring the clear nish:
The nished surface on the wood is a clear
lacquer coating. The lacquer nish can be
repaired if it becomes dull or is scratched.
Scratches extending into the wood will require
wood repair by lling the damaged area. If there
is light damage, the wood can be steamed to
bring the surface level.
Lacquer nish sheen can be restored by
carefully using 0000 steel wool or equivalent.
Sand damaged lacquer with ne sandpaper.
Once the scratched surface is smooth, apply a
clear lacquer coating using an aerosol. Lacquer
can be applied by cloth or brush, but best results
are obtained from an aerosol. If necessary, use
0000 steel wool or equivalent to bring out the
luster and smooth overspray.
CAUTION:
Use top coats and finishes in accordance
with the manufacturer’s safety instructions.
Use only in well ventilated areas with
proper respiratory filters and masks.
Re-staining the wood:
If bare wood is visible at the bottom of the
scratch, the wood will need to be re-stained. To
remove damaged varnish, lightly roughen a small
area around the scratch with sandpaper, steel
wool or synthetic steel wool. Find a stain that is
a shade lighter than the wood nish. Stain the
bare wood with a very small amount of stain on a
rag, brush or cotton swab. If the color is too light,
apply additional coats. Rub away excess stain
with a dry rag. If the wood becomes too dark, use
a rag moistened in mineral spirits to lighten the
wood. Select a lighter color stain and continue.
Several companies have simplied this repair
process by designing oil-based wood stain into
marker-like containers to rub on to the scratch.
Torn and scratched wood bers will absorb
stain and quickly darken. Start with a stain color
that is lighter than the original nish. A second
coat can always be applied if the color of the
rst coat is too light. Once the color is blended,
patch the clear nish as described above and
apply a wipe-on nish.
COUNTERTOPS
Solid Surface
Routine Care:
The motorhome solid surface countertops and
sinks have a matte/satin nish. Soapy water
or ammonia-based cleaners will remove most
dirt and stains from tops and bowls. Individual
techniques may be used to remove different
stains. Use the following the recommendations
for solid surface care.
Cleaning the Countertops:
Most dirt and stains: Use soapy water
or ammonia-based cleaner.
Water marks: Wipe with damp cloth
and towel dry.
Difcult stains: Use soft scrub and a
gray Scotchbrite
®
pad.
Disinfecting: Occasionally wipe surface
with diluted household bleach (one part
water and one part bleach).
Cleaning the Solid Surfaces Sink:
Occasionally clean by using Soft Scrub Liquid
Cleanser
®
and a gray Scotchbrite
®
pad. Scrub
the sink, rinse and towel dry.
Removing Cuts and Scratches:
Solid surface countertops are completely
renewable. Use the following instructions to
remove minor cuts and scratches.
Sand area starting with 180 grit
sandpaper, working your way up to 2000
grit or until blemish is gone and renewed
nish is achieved.
Never sand in one small area. Feather
out lightly at each increase in sandpaper
grit to blend restoration.
Preventing Heat Damage:
Hot pans and heat-generating appliances,
such as frying pans or crockpots, can damage
the surface. To prevent heat damage, always
use a hot pad or a trivet with rubber feet to
protect the surface.
To Next Page
Loading...