Braun Aesculap Acculan 4 User Manual (English)

Other manuals for Braun Aesculap Acculan 4

Questions and Answers:

S
Samuel GarciaSep 12, 2025
What to do if the tool on my Braun Aesculap Acculan 4 won't attach or detach?
- T
  Tina PerezSep 12, 2025
  If the tool on your Braun Medical Equipment does not attach or detach, ensure you are using a tool that is compatible with the attachment. If the tool connector is deformed or defective, use a new tool. If the coupling on the attachment is deformed or defective, have the manufacturer repair the attachment. A dirty tool coupling can also cause this issue; try cleaning the tool or using a new one, and also clean the attachment.
M
Mark HughesAug 25, 2025
What to do if Braun Aesculap Acculan 4 Medical Equipment product becomes too hot?
- T
  tbraunAug 25, 2025
  If your Braun Medical Equipment is overheating, it might be due to excessive use; ensure you are following the operating instructions. Incorrect reprocessing or maintenance could also be the cause, so adhere to the preparation and care guidelines, and lubricate the product before sterilization. Other potential causes include fall damage or a blunt tool. If the product has fall damage, have it repaired by the manufacturer. If a tool is blunt, replace it.
S
Steven ThomasAug 25, 2025
Why Braun Aesculap Acculan 4 has insufficient power?
- R
  Ryan Brown PhDAug 26, 2025
  Insufficient power in your Braun Medical Equipment could stem from a defective product, in which case you should follow the operating instructions for preparation and care, lubricate the product before sterilization, and have the manufacturer repair it. It could also be due to a large amount of heat generated after a short time, so follow the operating mode instructions and have the manufacturer repair the product. A blunt tool can also cause this issue; if so, change the tool.
D
Devin LloydAug 26, 2025
What to do if speed control knob not working in Braun Aesculap Acculan 4?
- A
  Amy WilliamsAug 26, 2025
  If the speed control knob on your Braun Medical Equipment isn't working, first check if the product is in a locked OFF position and turn the safety catch to the ON position. If that doesn't work, the speed control knob may be stuck or defective, requiring repair by the manufacturer.
E
Evelyn WebsterSep 12, 2025
Why is the Kirschner wire not turning in my Braun Aesculap Acculan 4 Medical Equipment?
- E
  Eric GibsonSep 12, 2025
  If the Kirschner wire is not turning in your Braun Medical Equipment, first ensure that the Kirschner wire chuck is set correctly by adjusting the sleeve to the correct Kirschner wire diameter. Also, check that the clamping lever is closed. If it is open, close it. If the clamping lever was not pulled back with sufficient force, pull it back forcefully and hold it.
D
Dustin LinSep 16, 2025
What to do if Kirschner wire is not turning in my Braun GB641R Medical Equipment?
- J
  Jason GomezSep 16, 2025
  If the Kirschner wire is not turning in your Braun GB641R Medical Equipment, first, ensure that the Kirschner wire chuck is set correctly by adjusting the sleeve to the right Kirschner wire diameter. Also, make sure the clamping lever is closed. If it is open, close it. Finally, ensure that you are pulling back the clamping lever forcefully and holding it.
K
Kevin AllenSep 5, 2025
What to do if Braun Aesculap Acculan 4 saw blade has insufficient cutting performance?
- G
  George SmithSep 5, 2025
  If you're experiencing insufficient cutting performance with the saw blade of your Braun Medical Equipment, consider the following: * **Worn saw blade teeth:** Replace the saw blade. * **Weak battery:** Charge the battery. * **Worn or defective battery:** Replace the battery. * **Overheated saw blade:** Move the saw back and forth during sawing and ensure sufficient irrigation of the saw blade.
M
Misty StevensSep 5, 2025
Why does my Braun Aesculap Acculan 4 Medical Equipment have insufficient power?
- W
  William RiveraSep 6, 2025
  If the Braun Medical Equipment has insufficient power, here are a few possible reasons: * The product may be defective. Follow the operating instructions for preparation and care, lubricate the product before every sterilization, and have the manufacturer repair the product. * The product is operating in left rotation mode. If using a serrated tool, operate in right rotation. * A defective attachment is being used. Have the manufacturer repair the attachment. * The tool is blunt. Change the tool.
R
Robert GreenAug 31, 2025
Why does my Braun Medical Equipment product become too hot?
- C
  Christopher RobertsonSep 1, 2025
  If your Braun Medical Equipment product becomes too hot, it could be due to several reasons. It may be caused by excessive use, so follow the operating instructions. The attachment may be defective, so follow the operating instructions and lubricate the attachment before every sterilization. If it was damaged by a fall, have the manufacturer repair the attachment. A blunt tool can also cause overheating, so change the tool. Insufficient power can be a factor; use serrated tools only in clockwise mode. Also, check if the attachment is defective and follow the operating instructions. Replace blunt tools.
Z
Zachary MorenoAug 30, 2025
Why Braun Aesculap Acculan 4 Medical Equipment dermatome blade has insufficient cutting performance?
- J
  Jessica SmithAug 30, 2025
  If the dermatome blade on your Braun Medical Equipment has insufficient cutting performance, the dermatome blade may be blunted, so replace it. Also, the dermatome may need to be adjusted, so have the manufacturer repair the product.