How to fix a Braun Commercial Food Equipment clipping machine that won't start?
If your Braun Commercial Food Equipment clipping machine isn't starting, there might be a few reasons: * The Li-ion battery might not be loaded. Make sure to load the Li-ion battery. * The Li-ion battery might not be inserted. Ensure that the Li-ion battery is properly inserted. * The Li-ion battery could be defective. Try inserting a new Li-ion battery.
What to do if my Braun Commercial Food Equipment clipping machine pauses during operation?
If your Braun Commercial Food Equipment clipping machine pauses during operation, here are a couple of potential causes: * The Li-ion battery may have been deactivated by its protective circuit. Try switching the clipping machine off and then on again. * The Li-ion battery might be empty. Try inserting a new Li-ion battery.
What does it mean when the warning indicator lights up continuously on my Braun Commercial Food Equipment?
If the warning indicator e lights up continuously on your Braun Commercial Food Equipment after inserting the Li-Ion battery, it means that too high a temperature (>50°) is measured in the Li-Ion battery during the charging process. Remove the Li-ion battery from the charging bay, let it cool down, and then try the charging process again. If the problem occurs again, have the Li-Ion battery inspected by the manufacturer, see Technical Service.
Why is the warning indicator blinking on my Braun Commercial Food Equipment?
If the warning indicator 'e' is blinking on your Braun Commercial Food Equipment when the Li-Ion battery is inserted, it indicates a battery charging error, a foreign object on the contact system, or a defective Li-Ion battery. Remove the Li-Ion battery from the charging bay, clean the contact system, and then try the charging process again. If the problem persists, have the Li-Ion battery inspected by the manufacturer, see Technical Service.
How to fix no image on the monitor of Braun Aesculap Medical Equipment?
If there is no image on the monitor of your Braun Medical Equipment, first, ensure that all units are connected to mains power and switched on. Check the fuse in the camera and replace it if it's broken. Inspect the video cable, connect it if it is not connected, and replace it if it is defective.
Why is the image too dark on my Braun Aesculap Medical Equipment?
If the image on your Braun Medical Equipment is too dark, check the following: Ensure the camera head is connected to the camera control unit and the camera plug is dry. If you are using a light guide cable, try connecting a new one. Also, check if the light source is dimmed down and increase the light source intensity. Check if the camera brightness is regulated down and regulate camera brightness up. If the image is still dark even without the camera, use a different endoscope and have the defective endoscope repaired by the manufacturer.
What to do if there is unrealistic color representation on the monitor of Braun Medical Equipment?
If you are experiencing unrealistic color representation on the monitor of your Braun Medical Equipment, the issue might be caused by a white balance failure, so start white balance-adjustment. Another potential cause is a misadjusted monitor color setting, so reset to the factory setting. Finally, a defective video cable can cause this problem, so replace the video cable.
How to fix a fuzzy image on Braun Medical Equipment?
If the image on your Braun Medical Equipment appears fuzzy or poorly defined, it might be due to the object being out of focus. Turn the focusing ring on the endoscopic lens and adjust the focus until the image is sharp. Also, check for debris on the endoscope tip and clean it with a sterile cloth and isopropyl alcohol (70 %). Finally, if there is moisture on the camera cable plug, dry the plug with gauze before plugging it in at the camera socket.
Why is there a color bar diagram on the monitor of my Braun Aesculap?
If you see a color bar diagram on the monitor of your Braun Medical Equipment, it indicates that the camera cable is not connected to the camera control unit. Connect the camera cable to the camera control unit.
What to do if “System error” appears on the monitor OSD of Braun Medical Equipment?
If “System error” appears on the monitor OSD of your Braun Medical Equipment, the first step is to restart the camera, as this may be due to an internal product error.
Lists the components included in the camera system package.
Details additional equipment needed for endoscopic interventions.
Describes the system's purpose in medical endoscopy visualization.
Explains how the camera system captures and processes endoscopic images.
Outlines essential steps and precautions before operating the device.
Instructions for connecting and configuring the camera system components.
Procedures to verify the proper operation of the camera control unit and head.
Guidelines for the safe and effective use of the camera system.
Describes the self-aligning feature and locking mechanism of the PV471 camera head.
Explains the process of calibrating colors for realistic image rendition.
Details programmable buttons on the camera head and their functions.
Shows default assignments for buttons on the camera head.
Adherence to regulations and standards for sterile processing.
Information on products intended for one-time use and warnings against reprocessing.
Guidelines on cleaning agents, material compatibility, and potential damage.
Safety instructions and validated procedures for cleaning and disinfection.
Specific procedure for wiping electrical devices without sterilization.
Detailed steps for manual cleaning and immersion disinfection.
Instructions and warnings regarding sterilization methods for camera components.
Procedures for inspecting and maintaining the product after cleaning cycles.
Guidelines for packaging the product for storage or sterilization.
Recommendations for storing sterile and single-use products.
Step-by-step guide for replacing fuses in the device.
Specifies the environmental conditions for operation, storage, and transport.
General| Category | Medical Equipment |
|---|---|
| Manufacturer | Braun |
| Material | Stainless Steel |
| Sterilization | Autoclavable |
| Usage | Surgical Instruments |
To Next Page
