EasyManuals Logo

Cisco ATA 192 Administration Guide

Cisco ATA 192
142 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #139 background imageLoading...
Page #139 background image
is evaluated. Unless you have a special dial plan string to allow a null entry, the call is rejected. Default setting:
5
Syntax for the Dial Plan Timer
(Ps<:n> | dial plan )
s: The number of seconds; if no number is entered after P, the default timer of 5 seconds applies.
n: (optional): The number to transmit automatically when the timer expires; you can enter a valid number.
No wildcard characters are allowed because the number will be transmitted as shown. If you omit the
number substitution, <:n>, then the user hears a reorder (fast busy) tone after the specified number of
seconds.
Examples for the Dial Plan Timer
Allow more time for users to start dialing after taking a phone off hook.
(P9 | (9,8<:1408>[2-9]xxxxxx | 9,8,1[2 9]xxxxxxxxx | 9,8,011xx. | 9,8,xx.|[1-8]xx)
P9 After taking a phone off hook, a user has 9 seconds to begin dialing. If no digits are pressed within
9 seconds, the user hears a reorder (fast busy) tone. By setting a longer timer, you allow more time for
users to enter the digits.
xx This code allows the entry of one or more digits. Do not use a single x, allowing 0 or more digits.
This setting will produce unwanted results especially if you are deploying timers.
Create a hotline for all sequences on the System Dial Plan
(P9<:23> | (9,8<:1408>[2-9]xxxxxx | 9,8,1[2-9]xxxxxxxxx | 9,8,011xx. | 9,8,xx.|[1-8]xx)
P9<:23> After taking the phone off hook, a user has 9 seconds to begin dialing. If no digits are pressed
within 9 seconds, the call is transmitted automatically to extension 23.
Create a hotline on a line button for an extension
(P0 <:1000>)
With the timer set to 0 seconds, the call is transmitted automatically to the specified extension when the
phone goes off hook.
Interdigit Long Timer (Incomplete Entry Timer)
You can think of this timer as the incomplete entry timer. This timer measures the interval between dialed
digits. It applies as long as the dialed digits do not match any digit sequences in the dial plan. Unless the user
enters another digit within the specified number of seconds, the entry is evaluated as incomplete, and the call
is rejected. Default setting: 10 seconds
This section explains how to edit a timer as part of a dial plan. Alternatively, you can modify the Control
Timer that controls the default interdigit timers for all calls. See Reset the Control Timers, on page 132.
Syntax for the Interdigit Long Timer
L:s, ( dial plan )
s: The number of seconds; if no number is entered after L:, the default timer of 5 seconds applies. The timer
sequence appears to the left of the initial parenthesis for the dial plan.
Cisco ATA 191 and ATA 192 Analog Telephone Adapter Administration Guide for Multiplatform Firmware
131
Advanced Options for Phone Services
Interdigit Long Timer (Incomplete Entry Timer)

Table of Contents

Other manuals for Cisco ATA 192

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ATA 192 and is the answer not in the manual?

Cisco ATA 192 Specifications

General IconGeneral
Ports2 FXS ports
Network Interface10/100 Ethernet
Voice ProtocolSIP
Audio CodecsG.711, G.726, G.729
Operating Temperature0 to 40°C (32 to 104°F)
Storage Temperature-20 to 60°C (-4 to 140°F)
Humidity10 to 90% non-condensing
ComplianceFCC, CE, UL
Fax SupportT.38, G.711 pass-through

Related product manuals