Circular milling
P/N 63674, Rev. 9 Page 77
could damage the machine. It is acceptable to run a tool at less than
150 sfpm (45.72 smpm) as long as at 20 gpm (76 lpm) it is greater than
150 sfpm (45.72 smpm).
If the operator chooses to run the machine beyond the design
limitations, they do so at their own risk.
TABLE 4-2. MAXIMUM SFPM/SMPM CAPABLE FROM THE HYDRAULIC MOTOR AT 60 HZ AND 20 GPM (76 LPM)
Tooling
diameter
Optional hydraulic motor sizes
6.2 cu-in
(101.6
cucm)
8.0 cu-in
(131
cucm)
9.6 cu-in
(157.3
cu-cm)
11.9
cu-in
(195.0
cucm)
14.9
cu-in
(244.17
cu-cm)
18.7
cu-in
(244.2
cucm)
24.0
cu-in
(393.3
cucm)
29.8
cu-in
(488.3
cucm)
1"
(25 mm)
194 sfpm
(59.1
smpm)
151 sfpm
(46
smpm)
125 sfpm
(38.1
smpm)
101 sfpm
(30.8
smpm)
81 sfpm
(24.7
smpm)
64 sfpm
(24.7
smpm)
50 sfpm
(15.2
smpm)
40 sfpm
(12.2
smpm)
2"
(51 mm)
389 sfpm
(118.6
smpm)
302 sfpm
(92.1
smpm)
250 sfpm
(76.2
smpm)
202 sfpm
(61.6
smpm)
161 sfpm
(49.1
smpm)
129 sfpm
(39.3
smpm)
100 sfpm
(30.5
smpm)
80 sfpm
(24.4
smpm)
4"
(102 mm)
777 sfpm
(236.8
smpm)
603 sfpm
(183.8
smpm)
500 sfpm
(152.4
smpm)
403 sfpm
(122.8
smpm)
323 sfpm
(98.5
smpm)
258 sfpm
(78.6
smpm)
200 sfpm
(61.0
smpm)
160 sfpm
(48.8
smpm)
5"
(127 mm)
971 sfpm
(296.0
smpm)
754 sfpm
(229.8
smpm)
624 sfpm
(190.2
smpm)
504 sfpm
(153.6
smpm)
403 sfpm
(122.8
smpm)
322 sfpm
(98.2
smpm)
250 sfpm
(76.2
smpm)
200 sfpm
(61.0
smpm)
6"
(152 mm)
1,166
sfpm
(355.4
smpm)
905 sfpm
(275.8
smpm)
749 sfpm
(228.3
smpm)
605 sfpm
(184.4
smpm)
484 sfpm
(147.5
smpm)
386 sfpm
(117.7
smpm)
300 sfpm
(91.4
smpm)
240 sfpm
(73.2
smpm)
8"
(203 mm)
1,554
sfpm
(473.7
smpm)
1,206
sfpm
(367.6
smpm)
905 sfpm
(275.8
smpm)
806 sfpm
(245.7
smpm)
645 sfpm
(196.6
smpm)
515 sfpm
(157.0
smpm)
400 sfpm
(121.9
smpm)
320 sfpm
(97.5
smpm)
10"
(254 mm)
1,943
sfpm
(592.2
smpm)
1,508
sfpm
(459.6
smpm)
1,206
sfpm
(367.6
smpm)
1,008
sfpm
(307.2
smpm)
806 sfpm
(245.7
smpm)
644 sfpm
(196.3
smpm)
500 sfpm
(152.4
smpm)
401 sfpm
(122.2
smpm)
To Next Page
Loading...