Climax FF6300 - SETUP; RECEIPT AND INSPECTION

P/N 80679, Rev. 10 Page 25
3 SETUP
1IN THIS CHAPTER:
3.1 RECEIPT AND INSPECTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -25
3.2 P
REPARING THE MACHINE FOR USE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -26
3.2.1 P
RE-SETUP CHECK - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -26
3.2.2 A
SSESSING THE WORK AREA - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -26
3.3 L
IFTING AND RIGGING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -27
3.4 S
ETUP OVERVIEW FOR THE ID CHUCK MACHINE - - - - - - - - - - - - - - - - - - - - - - - - - - - - -28
3.5 I
NSTALLATION HAZARDS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -30
3.6 I
NSTALLING THE ID CHUCK IN THE WORKPIECE - - - - - - - - - - - - - - - - - - - - - - - - - - - - -32
3.7 OD
MOUNTING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -36
3.7.1 S
ETUP OVERVIEW FOR THE OD MOUNT MACHINE - - - - - - - - - - - - - - - - - - - - - - - - -37
3.7.2 A
SSEMBLING THE OD MOUNT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -37
3.7.3 OD
MOUNTING ARRANGEMENTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -38
3.7.4 A
TTACHING THE OD MOUNT ASSEMBLY TO THE WORKPIECE - - - - - - - - - - - - - - - - - - - -40
3.7.5 C
ENTERING AND LEVELING THE OD MOUNT ASSEMBLY - - - - - - - - - - - - - - - - - - - - - -41
3.8 S
URFACE MOUNTING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -42
3.8.1 S
ETUP OVERVIEW FOR THE SURFACE MOUNT MACHINE - - - - - - - - - - - - - - - - - - - - - -42
3.8.2 A
SSEMBLING THE SURFACE MOUNT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -42
3.8.3 C
ENTERING AND LEVELING THE SURFACE MOUNT ASSEMBLY - - - - - - - - - - - - - - - - - - -43
3.9 P
OSITIONING THE MACHINING ARM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -44
3.10 P
OSITIONING THE COUNTERWEIGHT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -45
3.11 R
OTATING THE TOOL HEAD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -47
3.12 A
DJUSTING THE FEED BOX - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -48
3.12.1 A
DJUSTING THE FEED RATE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -49
3.12.2 C
ONDUCTING FEED ACTUATION MEASUREMENT - - - - - - - - - - - - - - - - - - - - - - - - -50
3.12.3 R
EVERSING THE FEED DIRECTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -51
3.12.4 D
ISCONNECTING FEED HOSES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -52
3.13 B
ACKFACING ATTACHMENT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -53
The FF6300 can machine a face, groove, or bevel on a flat flange. This chapter
explains how to set up the machine for these operating modes. and rigging.
3.1 RECEIPT AND INSPECTION
Your CLIMAX product was inspected and tested before shipment and packaged for
normal shipment conditions. CLIMAX does not guarantee the condition of your
machine upon delivery.
When you receive your CLIMAX product:
1. Inspect the shipping container for damage.
2. Check the contents of the shipping container against the included invoice to
check that all components have been shipped.
3. Inspect all components for damage.
4. Contact CLIMAX immediately to report damaged or missing components.