P/N 80679, Rev. 10 Page 79
APPENDIX A EXPLODED VIEWS AND PARTS LISTS
IN THIS CHAPTER:
FIGURE A-1. FEED BOX PNEUMATIC MANUAL FEED ADJUST (P/N 87326) - - - - - - - - - - - - - - - - - - - - - - - - 80
FIGURE A-2. AIR CONTROL ASSEMBLY FOR PNEUMATIC FEED (P/N 87941) - - - - - - - - - - - - - - - - - - - - - - - 81
FIGURE A-3. PNEUMATIC FILTER AND VALVE WITH STAND ASSEMBLY (P/N 59329) - - - - - - - - - - - - - - - - - - - - 82
FIGURE A-4. PNEUMATIC CONDITIONING UNIT 1/2" (13 MM) LOW-PRESSURE DROP-OUT (P/N 78264) - - - - - - - - - - - 84
FIGURE A-5. PNEUMATIC CONDITIONING UNIT 1/2" (13 MM) LOW-PRESSURE DROP-OUT PARTS LIST (P/N 78264) - - - - - - 85
FIGURE A-6. SLIDE TOOL HOLDER ASSEMBLY (P/N 79790) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 86
FIGURE A-7. SLIDE TOOL HOLDER ASSEMBLY PARTS LIST (P/N 79790) - - - - - - - - - - - - - - - - - - - - - - - - - 87
FIGURE A-8. MAIN BODY ASSEMBLY (P/N 87913) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 88
FIGURE A-9. MAIN BODY ASSEMBLY PARTS LIST (P/N 87913) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 89
FIGURE A-10. TURNING ARM ASSEMBLY 38" (965 MM) (P/N 80304) - - - - - - - - - - - - - - - - - - - - - - - - - - 90
FIGURE A-11. TURNING ARM ASSEMBLY 38" (965 MM) PARTS LIST (P/N 80304) - - - - - - - - - - - - - - - - - - - - - 91
FIGURE A-12. COUNTERWEIGHT ARM ASSEMBLY (P/N 80324) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 92
FIGURE A-13. BACKFACE ATTACHMENT ASSEMBLY (P/N 80362) - - - - - - - - - - - - - - - - - - - - - - - - - - - - 93
FIGURE A-14. OD MOUNT ASSEMBLY 38–63” (965–1,600 MM) (P/N 80477) - - - - - - - - - - - - - - - - - - - - - - 94
FIGURE A-15. OD MOUNT ASSEMBLY 38–63" (965–1,600 MM) PARTS LIST (P/N 80477) - - - - - - - - - - - - - - - - - 95
FIGURE A-16. OD MOUNT CLAMP KIT (P/N 80622) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 96
FIGURE A-17. FF6300 PNEUMATIC KIT (P/N 80969) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 97
FIGURE A-18. FF6300 HYDRAULIC KIT (6.2 CU.IN. MOTOR WITH QD FTG) (P/N 80970) - - - - - - - - - - - - - - - - - 98
FIGURE A-19. AIR VALVE ASSEMBLY (P/N 87916) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 99
FIGURE A-20. ID CHUCK ASSEMBLY 4 LEG 12–57" (305–1,448 MM) (P/N 81971) - - - - - - - - - - - - - - - - - - - 100
FIGURE A-21. LEVELING FOOT 4" (102 MM) ASSEMBLY (P/N 81977) - - - - - - - - - - - - - - - - - - - - - - - - - 101
FIGURE A-22. SURFACE MOUNT ASSEMBLY (P/N 82309) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 102
FIGURE A-23. AIR CONTROL ASSEMBLY FOR PNEUMATIC FEED AND 1/2" (13 MM) DRIVE SUPPLY (P/N 87917) - - - - - - 103
FIGURE A-24. HYDRAULIC KIT 6.2 CUBIC MOTOR (P/N 82555) - - - - - - - - - - - - - - - - - - - - - - - - - - - - 104
FIGURE A-25. BYPASS ASSEMBLY FOR SET UP OF HYDRAULIC MACHINE (P/N 83154) - - - - - - - - - - - - - - - - - 105
FIGURE A-26. BYPASS ASSEMBLY FOR SET UP OF HYDRAULIC MACHINE (P/N 83166) - - - - - - - - - - - - - - - - - 106
TABLE A-1. TOOL KIT (P/N 80327) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 107
TABLE A-2. RECOMMENDED SPARE PARTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 108
The following diagrams and parts lists are for your reference purposes only.
The machine’s limited warranty is void if the machine has been tampered
with by anyone who has not been authorized in writing by CLIMAX to
perform service on the machine.
To Next Page
Loading...
