Page 74
P785E Output #5 pulse time - Default 1 10 = 1 second Page 39
P786E Output #6 pulse time - Default 1 Page 39
P787E Output #7 pulse time - Default 1 Page 39
P788E Output #8 pulse time - Default 1 Page 39
** System Events to Scenario Mapping **
P791E Duress Alarm mapped to scenario 1-4 default 1 Page 51
P792E Keypad “Panic” (& buttons 1 & 3) mapped to scenario 1-4 default 1 Page 51
P793E Keypad “Fire” (buttons 4 & 6) mapped to scenario 1-4 default 1 Page 51
P794E Keypad “Medical” (buttons 7 & 9) mapped to scenario 1-4 default 1 Page 51
P795E Battery low mapped to scenario 1-4 default 1 Page 51
P796E Mains fail mapped to scenario 1-4 default 1 Page 51
P797E Phone line restore mapped to scenario 1-4 default 1 Page 51
P798E Radio PIR battery low mapped to scenario 1-4 default 1 Page 51
P799E Radio-key battery low mapped to scenario 1-4 default 1 Page 51
P800E Keypad tamper mapped to scenario 1-4 default 1 Page 51
P801E Cabinet tamper mapped to scenario 1-4 default 1 Page 51
P802E Zone tamper mapped to scenario 1-4 default 1 Page 51
P803E Radio panic mapped to scenario 1-4 default 1 Page 51
P804E Supervised Radio Timeout mapped to scenario 1-4 default 1 Page 51
P805E Zone Inactivity Timeout mapped to scenario 1-4 default 1 Page 51
P806E Test calls mapped to scenario 1-4 default 1 Page 51
Partition “D” Primary Output Options
P811E-P818E OPTIONS
P811E Area “D” primary options for output #1- Default 1 1 = Standard zone activation's Page 23
P812E Area “D” primary options for output #2 - Default 1 & 2 2 = Stay Mode activation's Page 23
P813E Area "D" primary options for output #3 - Default 1 3 = Radio key chirps Page 23
P814E Area "D" primary options for output #4 - Default 1 4 = All zones sealed (ready) Page 23
P815E Area "D" primary options for output #5 - Default 1 5 = 2 sec pulse on arm/disarm Page 23
P816E Area "D" primary options for output #6 - Default 1 6 = Day zone activation's Page 23
P817E Area "D" primary options for output #7 - Default 1 7 = Spare Page 23
P818E Area "D" primary options for output #8 - Default 1 8 = Spare Page 23
Partition “D” Keypad Options
P819E Arm key can disarm during exit - Default 1-8 Page 25
P820E Stay key can disarm during Stay armed state - Default 1-8 Page 25
Partition “D” Secondary Output Options
P821E-P828E OPTIONS
P821E Area "D" secondary options for output #1 - Default 0 1 = Any exclude Page 24
P822E Area "D" secondary options for output #2 - Default 0 2 = Auto exclude warn Page 24
P823E Area "D" secondary options for output #3 - Default 0 3 = Entry beeps Page 24
P824E Area "D" secondary options for output #4 - Default 0 4 = Exit Beeps Page 24
P825E Area "D" secondary options for output #5 - Default 0 5 = Control Page 24
P826E Area "D" secondary options for output #6 - Default 0 6 = Follow Set Arming Page 24
P827E Area "D" secondary options for output #7 - Default 0 7 = Follow Stay Arming Page 24
P828E Area "D" secondary options for output #8 - Default 0 8 = Follow Unset Page 24
Programming Partition “D” Auto Arm/Disarm Time-zones
P829E Time Zones used for Area "D" auto arming /disarming- Default 0 (see P832E) Page 25
Partition “D” Misc Options
P830E Misc partition options 1 - Default 0 1 = Cannot Arm if not sealed Page 25
2 = “Arm” required before code
3 = “Stay” required before code
4 = Code required to arm
5 = Code required to “Bypass” zones
6 = Control disables day zones
7 = Repeat System PA messages
8 = Spare
P831E Misc partition options 2 - Default 3,4,6 1 = Key-switch enabled Page 26
2 = Use 2nd Key-switch
3 = Key-switch ARM's/STAY
To Next Page
Loading...
