Why Datalogic Barcode Reader doesn't respond to external signal end?
If the Datalogic Barcode Reader does not respond correctly to the expected external signal end in On Line Mode and Serial On Line Mode, use the Genius™ software configuration program and select the OPERATING MODES folder to check the “Reading Phase Timeout” parameterization.
How to find the serial number on a Datalogic DS6300 Barcode Reader?
To obtain your unit's serial number, check the label above the connector panel of the Datalogic Barcode Reader. Alternatively, the serial number is displayed when connecting the device through the Genius™ program. Serial numbers consist of 9 characters: one letter, 2 numbers, another letter followed by 5 numbers.
How to troubleshoot Datalogic Scanner when the power LED is off?
If the “Power On” LED is not lit on your Datalogic Scanner, here are a few things to check: * Verify the power connection. * If using a power adapter (like PG6000), ensure it is connected to an AC source. * If using rail power, confirm that the rail has power. * If using C-BOX 100, check that it has power by checking the switch and LED. Also, verify whether you're using the 25/26-pin connector or the C-BOX 100 spring clamp connectors and measure the voltage either at pin 13 and pin 25 (for 25/26-pin connector) or at spring clamp 1 (for C-BOX 100).
What to do if Datalogic Scanner's 'Phase On' LED is lit but there are no reading results?
If the Master’s “Phase On” LED is correctly lit on your Datalogic scanner but you are not getting any reading results, ensure that the software configuration is consistent with the application condition and operating mode. Use the Genius™ software configuration program, select the OPERATING MODES folder, and check the related parameters.
What to do if Datalogic Barcode Reader's “Phase On” LED is lit but there are no reading results?
If the Master’s “Phase On” LED is correctly lit, but you're not getting any reading results, make sure your software configuration aligns with your application conditions. Use the Genius™ software and check the OPERATING MODES folder to verify related parameters.
How to configure Datalogic DS6300 Barcode Reader to respond correctly to the external signal end?
If your Datalogic Barcode Reader in On Line Mode or Serial On Line Mode isn't responding correctly to the expected external signal end, use the Genius™ software configuration program. Then select the OPERATING MODES folder and check the “Reading Phase Timeout” parameterization.
How to fix Datalogic DS6300 Barcode Reader when it is not possible to read the target barcode?
If your Datalogic Barcode Reader consistently returns 'No Read' when trying to scan a barcode, check the synchronization of the reading pulse with the object. Position the barcode in the center of the scan line and use the TEST MODE (selectable via Genius™ in Operating Modes). If issues persist, ensure the reading distance is within the allowed range (refer to the reading diagrams). Enable various code types (excluding Pharmacode) under the CODE tab and set LENGTH to Variable. Verify the barcode quality. If still unsuccessful, try the BARCODE TEST CHART included with the product.
Why is my Datalogic DS6300 not triggering in Serial On Line Mode?
To troubleshoot a Datalogic Barcode Reader that is not triggered in Serial On Line Mode, first, in the Genius™ program, check if serial on line is enabled as the “On Line options” parameter value in the OPERATING MODE folder. Also, verify that the Start-Stop strings are correctly assigned and that the serial trigger source is correctly connected and configured.
Why is no data appearing on the terminal from my Datalogic DS6300?
If data does not appear on the terminal, enable the DATA COMMUNICATION SETTINGS/MAIN- AUXILIARY PORT\DATA TX parameter in the Genius™ program.
How to troubleshoot a Datalogic DS6300 that won't power on?
If the “Power On” LED is not lit on the Datalogic Barcode Reader, check the following: 1. Is power connected? 2. If using a power adapter (like PG6000), is it connected to the wall outlet? 3. If using rail power, does the rail have power? 4. If using C-BOX 100, does it have power (check switch and LED)? Check if you are referring to the 25/26-pin connector or the C-BOX 100 spring clamp connectors. Measure voltage either at pin 13 and pin 25 (for 25/26-pin connector) or at spring clamp 1 (for C-BOX 100).
General| Scanning Technology | Laser |
|---|---|
| Interface | RS-232 |
| Reading Distance | Varies with barcode density and model; refer to specific model datasheet |
| Light Source | Laser Diode 650 nm (Visible Red Light) |
| Depth of Field | Varies with barcode density and model; refer to specific model datasheet |
| Operating Temperature | 0°C to 45°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 5% to 95% (non-condensing) |
| Electrical Safety | EN 60950-1 |
| EMC | EN 55022 |
| Laser Safety | Class 2, IEC 60825-1 |
To Next Page
