What to do if Denon Receiver power display flashes red?
If the power display on your Denon Receiver flashes red, it indicates that the amplifier circuit has failed. Switch off the power and please contact the DENON service adviser.
Why does my Denon Receiver AVR-1709 power off suddenly?
Your Denon Receiver AVR-1709 might be shutting down suddenly due to these reasons: * Speakers with impedance lower than specified are being used. * Speaker cable core wires are touching each other or contacting the rear panel. To resolve this: * Use speakers that meet the specified impedance. * Unplug the power cord, twist the core wires together tightly or apply termination treatments, and then reconnect.
Why does my Denon AVR-1709 Receiver turn off and the power indicator flashes red?
The protection circuit in your AVR-1709 may be activating due to a temperature increase in the internal components. Switch off the power immediately and allow the unit to cool down before reapplying power. Also, reinstall the AVR-1709 in a location with better ventilation.
What to do if my Denon Receiver remote control is not working properly?
If your Denon Receiver isn't responding to the remote control, consider these possible causes and solutions: * Replace the batteries with new ones. * Ensure you are operating the remote within the specified range. * Remove any obstacles between the remote and the receiver. * Verify the batteries are inserted correctly, matching the polarity marks. * Move the unit away from strong light sources that might interfere with the remote sensor. * Set the “Remote ID” for the main unit to “1”. * Ensure the SOURCE CONTROL switches are in the correct positions for the intended operation.
What to do if my Denon Receiver power does not turn on?
If your Denon Receiver isn't powering on or shuts off immediately after turning on, check the power cord connection to ensure it's properly inserted.
Why is there no sound from my Denon Receiver subwoofer?
If you're not getting any sound from your subwoofer connected to the Denon Receiver, consider the following: * Ensure the subwoofer is powered on. * Check that the “Subwoofer” setting in “Speaker Setup” is set to “Yes”. * Verify all connections to the subwoofer are correct. * Adjust the subwoofer's volume to an audible level.
Why can't I record a picture with my Denon AVR-1709 Receiver?
The video conversion function does not work for the REC OUT connectors. Match the input source and recorder connections.
How to turn on display on Denon AVR-1709 Receiver?
If the display is off on your Denon Receiver, the Dimmer setting is likely set to “OFF”. Change the Dimmer setting to something other than “OFF”.
Why does no picture appear on my Denon AVR-1709 Receiver?
If you're not seeing a picture on your Denon AVR-1709 Receiver, consider these potential causes: * Faulty connections between the receiver and the monitor. * Incorrect input setting on the monitor. * Incompatible connections between the player and monitor (e.g., player using component, monitor using video). To resolve this: * Check all connections. * Ensure the monitor input is set correctly. * Match the connection types between the player and monitor.
Why is there no sound from the surround back speaker on my Denon AVR-1709 Receiver?
If there's no sound from the surround back speaker, here are some possible reasons: * The surround back speaker’s power amplifier is assigned to a different channel. Check the setting and change it if necessary. * Surround back speaker setting is set to “None”. Set it to something other than “None”. * The “Parameter” – “Surround Parameter” – “SB CH OUT” settings are “OFF”. Please set “Parameter” – “Surround Parameter” – “SB CH OUT” to settings other than “OFF”. * Surround mode is not set to a mode for 6.1- or 7.1-channel playback. Select a surround playback mode.
General| Number of Channels | 7.1 |
|---|---|
| HDMI Inputs | 3 |
| HDMI Outputs | 1 |
| HDMI Version | 1.3a |
| Component Video Inputs | 2 |
| Component Video Outputs | 1 |
| Digital Audio Inputs | 2 Optical, 2 Coaxial |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 100 dB |
| THD | 0.08% |
| Input Impedance | 47 kOhm |
| Input Sensitivity | 200 mV |
| Tuner Presets | 56 |
| HDMI Switching | Yes |
| Tuner Type | AM/FM |
| Preset Stations | 56 |
| Auto Calibration | Yes (Audyssey MultEQ) |
| Power Consumption | 460 W |
| Standby Power Consumption | 0.3 W |
| Power Output | 80 W per channel (8 ohms, 20 Hz - 20 kHz, THD 0.08%) |
| HDMI Features | Deep Color, x.v.Color |
| Dolby Formats | Dolby Digital, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby TrueHD |
| DTS Formats | DTS, DTS-ES, DTS 96/24, DTS Neo:6, DTS-HD Master Audio |
| Audio Decoders | Dolby Digital, DTS |
| Amplifier Output Details | 80 watts per channel (8 ohms, 20Hz-20kHz, 0.08% THD) |
| Video Inputs/Outputs | Composite |
| Audio Inputs/Outputs | Digital Optical |
| Remote Control | Yes |
| Dimensions | 434 x 171 x 377 mm |
| Weight | 21.6 lbs (9.8 kg) |
To Next Page
