ENGLISH
•
To
proceed to "Step 5" without checking the analysis result, use
1:::.
\l
to select "Store<"
while "Parameter Check<"
is
displayed.
• Values that
are
different from the actual distance may
be
set for speakers with built-in filters
(subwoofers, etc). This
is
because filters
add
electrical delay to the signal that should
be
compensated.
IPJ
Error Messages
If
the auto setup procedure could not
be
completed due to speaker installation, the measuring environment,
etc.
an
error message is displayed. Check the relevant items and
be
sure to take the necessary measures. After
addressing any issues, perform the auto setup procedure over again.
1
F:
;.,
b ;
en
t
rj
c ; s e I •
:~~ur~~c~e:~~~:~:nt~~o
~~o::;ad~r
•
~~~:r
~~~o~:
i~~~~~Vice
generating
-----'-:..:..:..::....:....::..:..-----'----'-'------'--=-=---
__
---..J •
Try
again when the surroundings
are
quieter.
• Speaker or subwoofer sound
is
too • Check the speaker installation and the
low for accurate measurements to
be
direction
in
which the speakers
are
made. facing .
• Adjust the subwoofer's volume.
setup
Cause
Measures
speaker could not
be.
Check the connections of the
displayed speaker.
Error
messages (examples)
1 Ca
'-'
t ;
co
n " 5 F
rj
co
n
;~
I·
~~~~~~~~d
---='--'t::....::......:....:.-=--'---=--------'-.:....::.....:...:::.--
.
The
front L and front R speakers
The messages alternate were not properly detected.
· Only one channel of the surround
speakers was detected.
· Sound was output from the R
channel when only one surround
back
speaker was connected.
·
The
surround
back
speaker was
detected, but the surrounds were
not detected.
I----'--'-'-FI;·
I
I
1'1,
'.::'
,-
5 F :
r1
(;
n
E'
I·
:~~~~~~~~ed
setup microphone
is
not •
~~~r~~~tone
~~e<SE~~c~u~~g>.
-----'------'------'--=--:..-----'-::...:....-----'------'--'-=-
__
---..J • Not
all
speakers could
be
detected. • Check the speaker connections.
)
)
When analysis
is
complete, "Parameter Check<"
is
displayed.
Press
<l
and check the analysis results for the following four items.
CD
Make your selection using
1:::.
\l
and
press
<l.
• Presence and
size
of speaker
"SpConfig. Check<"
• Distance of speaker from listening position
"Distance Check<"
• Speaker channel level
"Ch Level Check<"
• Crossover Frequency
"CrossoverCheck<"
@ Use
1:::.
or
\l
to change which speaker
is
displayed.
OTo
switch
to
another analysis result item
Press
ENTER.
This returns you to analysis results items,
so
repeat operation
CD.
( Step 4 : Check
oTo proceed
to
"Step 5 : Store"
During display of crossover frequency result or analysis results item, press
ENTER.
• "Store<"
is
displayed.
( Step 5 : Store
•
Select"
Retry" to make the measurements again.
-n
...
4 Be sure to turn the power off before checking speaker connections.
The auto setup measurement results
are
stored
in
the AVR-1709.
CD
Press
<l
while
"Store<"
is
displayed.
• "Storing" blinks on the display panel while the results
are
being stored.
• When storing
is
complete, "Completed"
is
displayed followed by "Disconnect
Mic".
@ Disconnect the setup microphone from the AVR-1709.
OTo
cancel storing
Use
1:::.
or
\l
to display
"Cancek"
while "Store<"
is
displayed
and
press
<l.
• All the measured auto setup
data
will
be
erased.
-n·
..
4
Do
not turn the power
off
while the settings
are
being stored.
I
•
Displayed speaker connected
the polarities reversed.
---=-=-=------=-----'----'------='-=--=------
t
The
messages alternate
1---=--=-_,
L'
~=----
__
I
with • Check the polarities of the displayed
speaker.
•
For
some speakers, this error
message may
be
displayed even if the
speaker
is
properly connected. If the
connection
is
correct, use the
1:::.
or
\l
buttons to display "Skip<"
and
then
press
<l.
21
To Next Page
Loading...
Need help?
General
