ENGLISH
C
Dynamic
EO
/
Volume:
ON
--
Dynamic
EO
:
ON
/
Volume:
OFF
~
-
Dynamic
EO
/
Volume:
OFF
....
>.-------
Operating from the main unit or main remote
control unit
Press
<DYN
VOl>
or
[DYNAMIC
VOLUME].
-1
o
c
u
'"
'"
LI
Middle setting prevents loud
and
soft sounds from
being much louder
and
softer respectively than average
sounds.
Low setting provides the least adjustments to the
loudest
and
softest of sounds.
Day
Evening
fi1
DV Setting (Dynamic Volume Setting)
Set Dynamic Volume effect.
Abo.ut Dynamic
EQ
Audyssey Dynamic
EOTM
solves the problem of deteriorating sound
quality
as
volume
is
decreased
by
taking into account human
perception
and
room acoustics. Dynamic
EO
selects the correct
frequency response
and
surround levels moment-by-moment at
any user-selected volume setting.
The
result
is
bass
response,
tonal balance,
and
surround impression that remain constant
despite changes
in
volume. Dynamic
EO
combines information
from incoming source levels with actual output sound levels
in
the
room, a prerequisite for delivering a loudness correction solution.
Audyssey Dynamic
EO
works
in
tandem with Audyssey MultEO to
provide well-balanced sound for every listener at
any
volume level.
About DynamicVolume
Audyssey Dynamic
Volume™
solves the problem of large variations
in
volume level between television programs, commercials,
and
between the soft
and
loud passages of movies.
Dynamic Volume looks at the preferred volume setting
by
the user
and
then monitors
how
the volume of program material
is
being perceived
by listeners
in
real
time to decide whether
an
adjustment
is
needed.
Whenever necessary, Dynamic Volume makes the necessary rapid
or gradual adjustments to maintain the desired playback volume
level while optimizing the dynamic
range
Audyssey Dynamic
EO
is
integrated into Dynamic Volume
so
that
as
the playback volume
is
adjusted automatically, the perceived
bass
response, tonal balance,
surround impression,
and
dialog clarity remain the same whether
watching movies, flipping between television channels, or changing
from stereo to surround sound content.
-Nti'
•
• "DV Setting"
can
only
be
set when auto setup
has
been performed.
• "DV Setting" cannot
be
set
in
the following situations.
• If "Auto Setup" fails to
be
completed.
• After running Auto Setup, when the number of used speakers
has
increased from the number of measured speakers.
• If "Dynamic Volume" setting
is
"OFF':
[Selectable items]
I
Midnight
I:
High setting affects volume the most. causing
all
sounds
to
be
of equal loudness.
"Red"
Dynamic
EO
/
Volume:
OFF
"Green"
Dynamic
EO
I
Volume:
ON
--
Dynamic
EO
:
ON
/
Volume:
OFF
[~\i.'2~~~!'J] [~\i.'2~~~!'J]
~«-
~-
~
Operating from the main unit or main remote
control unit
Press
<DYN
VOl>
or
[DYNAMIC
VOLUME].
fi Dynamic Volume
Audyssey Dynamic Volume solves the problem of large variations
in
volume level between television programs, commercials,
and
between
the soft
and
loud passages of movies.
Audyssey Dynamic
EO
is
integrated into Dynamic Volume
so
that
as
the playback volume
is
adjusted automatically, the perceived
bass
response, tonal balance, surround impression,
and
dialog clarity
remain the same.
-Nti'.
• "Dynamic Volume"
can
only
be
set when auto setup
has
been
performed.
• "Dynamic Volume" cannot
be
set
in
the following situations.
• If "Auto Setup" fails to
be
completed.
• After running Auto Setup, when the number
of
used speakers
has
increased from the number of measured speakers.
•
When"
MultEO"
is
set to "OFF", "Dynamic EO"
is
automatically set
to "OFF".
• "Night Mode"
and
"Tone Control" cannot
be
used jointly.
[Selectable items]
ON
Use Dynamic Volume.
The
Dynamic Volume effect will
be
at the level of the "DV
Setting".
~:
Do
not use Dynamic Volume.
Before running Auto Setup
and
after running Auto Setup, if the number
of speakers
has
increased or
you
pressed
<DYN
VOl>
or
[DYNAMIC
VOLUME],
"Run Audyssey"
is
displayed.
In
this
case,
either perform
Auto Setup again, or return to the setting after running Auto Setup with
"System Setup" - "Speaker Setup" - "Restore".
)
• DynamlcEQ
<;
PI
DynamicVolume
(
PI
DV
Setting
OOperating conditions for
each
function
• Dynamic EQ: When
"MultEO"
is
set to
"ON"
• Dynamic Volume: When "Dynamic EO"
is
set to
"ON"
•
DV
setting: When "Dynamic Volume"
is
set to
"ON"
Before running Auto Setup
and
after running Auto Setup, if the number
of speakers
has
increased or
you
pressed
<DYN
VOl>
or
[DYNAMIC
VOLUME],
"Run Audyssey"
is
displayed.
In
this case, either perform
Auto Setup again, or return to the setting after running Auto Setup with
"System Setup" - "Speaker Setup" - "Restore".
1m
Dynamic
EQ
Audyssey Dynamic
EO
solves the problem of deteriorating sound
quality
as
volume
is
decreased
by
taking into account human perception
and
room acoustics. Audyssey Dynamic
EO
works
in
tandem with
Audyssey MultEO to provide well-balanced sound for every listener
at any volume level.
-N,n.
• "Dynamic EO"
can
only
be
set when auto setup
has
been
performed.
• "Dynamic EO" cannot
be
set
in
the following situations.
• If "Auto Setup" fails to
be
completed.
• After running Auto Setup, when the number of used speakers
has
increased from the number of measured speakers.
•
When"
MultEO"
is
set to "OFF': "Dynamic EO"
is
automatically set
to "OFF".
• "Night Mode"
and
"Tone Control" cannot
be
used jointly.
[Selectable
items]
~:
Use Dynamic
EO
function.
OFF
Do
not use Dynamic
EO
function.
For details on adjusting individual parameters, see "Adjusting
the
parameters" (D3f"page 33).1 36
To Next Page
Loading...
Need help?
General
