Denon AVR-1709

ENGLISH
[Remote Control Unit]
jJ
'"
3
o
...
'"
n
o
~
£
,
r--
s
c
~
N
o
:l
'"
[Audio)
Symptom
"
CMJse
.-;..
Couirtenn...ure
.,
Page
No sound is
• You
are playing
a
monaural
• The mode
is set to something
31
produced from source (TV, AM radio broadcast,
other than "STANDARD" (Dolby/
center speaker.
etc.)
in the "STANDARD" (Dolby/ DTS Surround).
DTS Surround) mode.
No sound
•
The surround
mode
is
set to
• Set
to a
surround playback
32
is produced "STEREO" or "DIRECT': mode.
from surround
speakers.
No sound
is
·The
surround back speaker's
• Check the setting
and change it
28
produced from power amplifier
is assigned to a
as necessa ry.
surround back
different channel.
speaker.
• Surround
back speaker setting is
• Set
to something other
than 23
set to "None': "None':
·The
"Parameter"
-
"Surround
•
Please
set
"Parameter" -
35
Parameter"
- "SB
CH OUT" "Surround
Parameter" - "SB
settings
are "OFF': CH OUT" to settings other than
"OW:
• Surround mode not set to a mode
• Select
a
surround playback
31,32
for 6.1- or 7.1-channel playback. mode.
No sound is • Subwoofer's power not turned • Turn on the subwoofer's power.
-
produced from
on.
subwoofer.
·The
"Subwoofer" setting
at
• Set to
"Yes ':
23
"Speaker Setup" is set to "No':
•
The subwoofer is not properly
•
Check the connections.
9
connected.
·The
subwoofer's volume is
• Adjust the subwoofer's
volume 45
turned off. to
an appropriate level.
No test tones
are
• Surround
mode not set to
• Set to the "STANDARD"(Dolby/
31
produced when
"STAN DARD" (Dolby/DTS DTS Surround) mode.
main remote
Surround).
control unit's
TEST button is
pressed.
DTS sound is not • DVD player's audio output setting • Set the DVD player. For details,
-
output.
is not set to bitstream. refer
to
the
DVD player's
operating instructions.
·DVD
player
is
not compatible
•
Use a DTS-compatible player.
-
with
DTS sound playback.
•
The AVR-1709's "Input
Mode"
• Set
to
the
"Auto"
or
"DTS"
39
setting
is set to
other
than mode.
"DTS':
3
3
3
3
3
30
Page
40,42,43,
47 - 49
• Replace with
new batteries.
• Operate within the specified
range.
• Remove the obstacle.
CoUntermeasure
• Set "Remote 10" for the main
unit to
"1 ':
• Set the SOURCE CONTROL
switches to the correct positions
according the operation
you are
applying.
• Insert the batteries
in the
proper direction, following the
polarity marks
in the battery
compartment.
• Move the set to a place
in which
the remote control sensor will
not
be exposed to strong light.
.Cauu
• Batteries are worn.
•
You are operating outside of the
specified range.
• Obstacle between main unit
and
remote control unit.
•
The batteries are not inserted in
. the proper direction, as indicated
by the polarity marks in the
battery compartment.
•
The set's remote control sensor
is exposed to strong light (direct
sunlight. inverter type fluorescent
bulb light, etc.).
•
The remote 10 of the main unit
and remote control unit do not
, match.
•
The SOURCE CONTROL switches
are not set in the correct
positions.
SymptOJn
Set does not work
properly when
remote control
unit operated.
64