Dion-Ag F41 - Page 107

To Next Page

To Previous Page

107

LUBRICATION

Figure 145 Grinder adjusting rod and adjustment springs

Figure 146 Transmission actuator pivots Figure 147

Manual No. F4117E987E V1.1

Main Page

Default Chapter4
- Table of Contents4
Specifications8
Serial Number Location9
Check List10
- Pre-Season Checks10
- Daily Checks11
Foreword12
- To Our Customer12
- This Manual Should Remain with the Machine When Sold12
- Warranty Information12
- Warranty on the Metal Detector12
- Safety12
Safety Rules13
- Safety Alert Symbol13
- Danger, Warning and Caution13
- Decals13
- Follow a Safety Program13
- A Word to the Operator13
- Pto Operation15
- Mandatory Stopping Procedure15
- Guards and Shields16
Safety Sign Location17
- Safety Sign Application Procedure21
- Material Supplied Separately with the Machine22
- Harvesters Are Shipped to Operate as Follows22
- Optional Equipment Choices22
Delivery22
- Manual Jack23
- Receiving Your Forage Harvester23
- Preparing the Forage Harvester23
Assembling Instructions23
- Installing the Control Box24
- Installing the Control Box (F41 Stinger Model Only)24
- Connecting the Power-Take-Off (Pto)26
- Installing the Foldable Spout (F41 Model Only)27
- INSTALLING the 12" (30 CM) SPOUT EXTENSION (F41 MODEL ONLY) FIGURE 1228
- Installing the 24" (60 CM) Spout Extension (F41 Model Only)29
- How to Make the Electrical Connections on the Spout (F41 Model Only)31
- Installing the Closing Plate on the Spout32
- Installing Mudguards over Tandem Wheels33
- Installing an Attachment on the Forage Harvester34
- Installing the Recutter Bar Assembly for Corn Crop36
- Installing the Grain Pan and Front Rubber Pad Assembly for Corn Crop36
- Installing a Light on the Spout Deflector (F41 Model Only)37
- Installing the Inspection Light37
Assembling Instructions - Liquid Incorporation System39
- Installing a Second Tank48
Assembling Instructions - Manual Quick-Disconnect Hitch51
Assembling Instructions - Electric Quick-Disconnect Hitch (up to 2017)52
Assembling Instructions - Electric Quick-Disconnect Hitch (2017+)54
Assembling Instructions - Draw Bar Extension58
Assembling Instructions - Transport Lights60
Corn Cracker Installation Instructions61
Partial Dismantling of the Corn Cracker for Hay Crop76
Partial Reassembling of the Corn Cracker for Corn Crop83
Hydraulic Spout Conversion88
- Break-In Speed90
- Bolt Torque Specifications90
- Metal Detector90
- Stopping the Machine90
- Transportation on Public Roads90
Operating Instructions90
- Transport Position - F41 Stinger91
- Preparing for Field Operation92
- Hitching the Forage Harvester to the Tractor92
- Adjusting the Attachment Ground Clearance93
- Starting up93
- Information on the Metal Detector94
- Daily Checks on the Metal Detector94
- Initializing the Metal Detector95
- (Starting up the Machine with Metal Detector)95
- Stopping the Machine95
- Starting Operation96
- The Control Box96
- Emergency Stop96
- Operating Instruction for the F41 Stinger Spout96
- What to Do When the Machine Detects a Ferrous Metal97
- What to Do if Material Accumulation Occurs (Clogging)98
- How to By-Pass the Metal Detector99
- Shear Bolt100
- Pressure and Flow Charts for Standard Nozzle101
- Standard Nozzle for Water Spraying Teejet Xr8004Vs101
- How to Operate the Liquid Incorporation System101
- Calibration Procedures101
- Pressure Adjustment101
- Detection System for Safety Bolt Breakage or Friction Clutch Slippage on the Cutter Head Transmission Shaft102
- Transport Light103
- Hydraulic Circuit104
- Power-Take-Off (Pto)104
- Lubrication Chart104
- Chains Lubrication104
- Gear Box Lubrication104
Lubrication104
- Corn Cracker Lubrication111
Adjustments - Maintenance113
- Wheel Positioning113
- Ground Clearance114
- Dismantling and Reassembly of the Power-Take-Off (Pto) Rotating Guards114
- Forage Harvester Draw Bar115
- Feed Roll Balancing Springs115
- Upper Feed Roll Chain Tension116
- Lower Feed Roll Chain Tension116
- Straw Chopping116
- Balancing Springs 2117
- Upper Roll Adjusting Bolts118
- Magnetic Drain Plugs118
- Spout Wear Plate (F41)119
- Spout Wear Plate (F41 Stinger)119
- Hydraulic Spout Cylinder Stroke Adjustment (F41 Stinger)120
- Adjusting the Free Rotation of the Spout121
- Rotation Motor Adjustment (F41 Stinger)122
- Feed Roll Stopping System123
- Fan Belt Tension124
- Fan and Transmission Belt Replacement124
- Corn Cracker Belt Tension125
- Corn Cracker Belt Replacement126
- Transmission Box Belts127
- Reverse, Neutral and Forward Speeds Positions127
- Angle Drive Transmission Box Sheave128
- Fan Adjustment129
- Knife Adjustment131
- Knife Grinding132
- Knife Replacement134
- Knives & Shear Bar General Information134
- Shear Bar Adjustment135
- Daily Adjustment (after Knives Have Been Ground)135
- Replacement and Initial Adjustment of the Shear Bar136
- Cutting Length Selection137
- Procedure for Changing the Cutting Length138
- Procedure to Increase the Forage Harvester's Feeding Speed by 33139
- Smooth Feed Roll Cleaner Adjustment140
- Maintenance Procedure for the Cutter Head Bottom Plate Assembly141
- Maintenance Procedure for the Fan Bottom Plate Assembly142
- Corn Cracker Sheave Alignment144
- Corn Cracker Q.D. Bushings145
- Corn Cracker Lower Roll Bearings145
- Corn Cracker Upper Roll Bearings147
- Corn Cracker Lower Roll Half Bottom Plate149
- Corn Cracker Roll Scraper151
- Upper Corn Cracker Roll "Zero" Position Adjustment152
- Upper Cracker Roll Pressure and Gap Adjustment153
- Corn Cracker Initial Start up Adjustment154
- Lifting the Attachment154
- Lifting Arms154
- Stone Carriage Adjustment155
- Stone Replacement155
- Cutter Head Sensor Adjustment156
- Feed Roll Shaft Sensor Adjustment156
- Pto Friction Clutch Adjustment (Option)157
- Venting the Clutch158
- Clutch Dismantling Procedure159
- Clutch Assembling Procedure160
- Clutch Torque Setting161
- Transmission Clutch Lever Position Sensor162
- Disassembling and Assembling the Radial Pin Clutch (Torque Limiter)163
- At the End of the Season, It Is Recoended to Proceed as Follows167
Metal Detector Diagnostic Short Procedure168
Led" Display on Metal Detector169
Jumper Position169
Troubleshooting170

Dion-Ag F41 - Page 107

Table of Contents