Why is the audio quality poor with low bass response on my Elan Network Router?
If the audio quality is poor and unclear, and the bass response is low with your Elan Network Router, carefully check the polarity of each speaker. Isolate the issue to the source or zone and correct it. Also, try increasing or decreasing the source level (+9/-6dB).
What to do if WHM, Paging, Doorbell, System Off do not function in Chassis #2-4 of my Elan Network Router?
If you are experiencing issues where the WHM, Paging, Doorbell, and System Off functions do not work, the sense information is incorrect, IR information does not reach the source equipment, or the system On/Off status is incorrect in Chassis #2-4 only of your Elan Network Router, connect the Expansion Port OUT of Chassis #1 to the Expansion Port IN of Chassis 2, etc., using ELAN’s S12XK Expansion Kit.
How to fix no RS-232 control of S86A or sources in Chassis #2-4 of my Elan Network Router?
If you are experiencing issues where there is no RS-232 control of S86A or sources in Chassis #2-4 only of your Elan Network Router, connect the RS-232 Serial Port OUT of Chassis #1 to the RS-232 Serial Port IN of Chassis 2, etc., using ELAN’s S12XK Expansion Kit.
General| Category | Network Router |
|---|---|
| Frequency Band | 2.4 GHz |
| Maximum Speed | 300 Mbps |
| Antennas | 2 external antennas |
| Model | s86a |
| Wireless Standards | 802.11b/g/n |
| Ports | 4 x 10/100 Mbps LAN, 1 x 10/100 Mbps WAN |
| Security | WPA, WPA2, WEP |
Describes the manual's goal.
Outlines the manual's structure and content.
Details crucial safety practices for operation and maintenance.
Background on the company and its history.
Lists key features and capabilities of the S86A controller.
Details the functions and indicators of the S86A unit.
Describes the controls and indicators on the front of the S86A.
Details the connections and indicators on the rear of the S86A.
General overview of system design principles for the S86A.
Instructions for mounting the S86A in an equipment rack.
Explains pre-wiring recommendations for system setup.
Describes typical system applications for the S86A.
Explains the concepts of zones and sub-zones in the system.
Details how to configure independent stereo zones with the S86A.
Explains how to set up a stereo zone with an independent stereo sub-zone.
Describes setting up a stereo zone with an independent mono sub-zone.
Details configurations for stereo zones with multiple sub-zones.
Explains how to use the S86A for video distribution.
Describes the SPP panel for system connectivity.
Details rear connections when using the SPP panel.
Details front connections when using the SPP panel.
Explains how to connect VIA! Touch Panels.
Details connections for Olé Film Interactive Touchpads.
Describes the "A" punchdown locations for touchpads.
Details the "B" punchdown locations for 16VDC power.
Details the "B" punchdown locations for 12VDC power.
Describes the "C" punchdown locations.
Details how to connect ELAN Z•Pad keypads.
Explains how to connect IR receivers.
Details connecting ELANSENSE Sensors.
Describes how to connect programmable triggers.
Explains linking multiple S86A chassis.
Details connecting external power supplies.
Explains RS-485 expansion connections.
Discusses various switches affecting controller function.
Explains the INT 12V-EXT 16V switch.
Details the ZNET/VNET switch.
Describes the SS/SC4 switch.
Details connections for Zones 1-8.
Describes the VIA!NET connection on the front panel.
Notes that EXT IR is not used for S86A.
Details connecting Sense Inputs on the front panel.
Explains SS/SC4 integration.
Details Zone 1-8 connections to SPP.
Explains the use of programmable trigger outputs.
Details connecting power supplies to the SPP.
Details connections directly to the S86A without SPP.
Explains connecting Sense Inputs directly to the S86A.
Details VIA! Touch Panel connections without SPP.
Explains Olé Touchpad connections without SPP.
Details Keypad connections without SPP.
Describes programmable trigger outputs.
Explains the system trigger output.
Discusses direct S86A connections.
Details source-specific IR output connections.
Explains the ALL IR OUT port.
Details audio and video source connections.
Explains how to use loop outputs for sharing sources.
Discusses composite video switching.
Explains the use of the V8 Video Controller.
Details the VIA!QUAD video processor.
Discusses component video switching.
Explains the V85 Component Video Controller.
Details audio outputs for zones.
Details video outputs for zones.
Explains speaker output connections.
Details RS-232 ports.
Explains SC-4 controller connection.
Details SS1 System Station connection.
Explains C2 controller connections.
Details VSE2 volume control connections.
Explains connecting multiple S86A chassis.
Details loop output/source input connections for multi-chassis.
Details multi-chassis source IR expansion.
Details multi-chassis VIA!NET connections.
Details multi-chassis RS-232 connections.
Details multi-chassis C2 connections.
Details AC power connection.
Describes the front panel access door.
Explains Unit ID DIP switch configuration.
Shows UNIT ID DIP switch settings.
Describes the front panel LEDs.
Provides general info on RS-232 serial interface.
Details the communication port settings for RS-232.
Lists system-level commands.
Command for controlling zone bass levels.
Command for Do Not Disturb function.
Command for Doorbell function.
Command for system-wide zone control.
Command to control zone mute function.
Command for zone power on/off/toggle.
Command to select source in a zone.
Command to turn all zones off.
Command for controlling zone treble levels.
Command for controlling zone volume.
Command for Whole House Music function.
Command to control zone loudness.
Command to enable/disable Page function.
Command for programmable trigger outputs.
Command to switch video inputs.
Command to switch audio inputs.
Introduces query commands.
Query for audio signal presence.
Query for page trigger status.
Query for sense trigger input status.
Query for video signal presence.
Query for firmware version.
Query for chassis status data.
Query for zone names.
Query for source names.
Command to reset system to defaults.
Details the RMK3 rack mount kit.
To Next Page
