Endress+Hauser PROline promag 53 - Maintenance; 7.1 Exterior Cleaning; 7.2 Seals

PROline Promag 53 10 Technical data
Endress+Hauser 127
Pressure tightness
(liner)
Limiting flow see Page 21
Pressure loss • No pressure loss if the sensor is installed in a pipe of the same nominal diameter
(Promag H: only 3/8"/DN 8 and larger).
• Pressure losses for configurations incorporating adapters according to
(E) DIN EN 545 → Page 20
Promag W
Nominal diameter
Measuring
tube lining
Resistance of measuring tube lining to partial vacuum
Limit values for abs. pressure [psia] at various fluid temperatures
[mm] [inch] 77°F
(25°C)
158°F
(70°C)
176°F
(80°C)
212°F
(100°C)
266°F
130°C
302°F
(150°C)
356°F
(180°C)
25 - 2000 1 - 78" Polyurethane 0 0
−−−−−
65 - 2000 3 - 78" Hard rubber 0 0 0 −−−−
Promag P
Nominal diameter
Measuring
tube lining
Resistance of measuring tube lining to partial vacuum
Limit values for abs. pressure psia (mbar) at various fluid
temperatures
[mm] [inch] 77°F
(25°C)
176°F
(80°C)
212°F
(100°C)
266°F
(130°C)
302°F
(150°C)
356°F
(180°C)
15 1/2" PTFE
0 0 0 1.5 (100) – –
25 1" PTFE / PFA
0 / 0 0 / 0 0 / 0 1.5 (100) / 0 – / 0 – / 0
32 − PTFE / PFA
0 / 0 0 / 0 0 / 0 1.5 (100) / 0 – / 0 – / 0
40 1 1/2" PTFE / PFA
0 / 0 0 / 0 0 / 0 1.5 (100) / 0 – / 0 – / 0
50 2" PTFE / PFA
0 / 0 0 / 0 0 / 0 1.5 (100) / 0 – / 0 – / 0
65 − PTFE / PFA
0 / 0 * 0.6 (40) / 0 1.9 (130) / 0 – / 0 – / 0
80 3" PTFE / PFA
0 / 0 * 0.6 (40) / 0 1.9 (130) / 0 – / 0 – / 0
100 4" PTFE / PFA
0 / 0 * 2.0 (135) / 0 2.5 (170) / 0 – / 0 – / 0
125 − PTFE / PFA
2.0 (135) / 0 * 3.5 (240) / 0 5.6 (385) / 0 – / 0 – / 0
150 6" PTFE / PFA
2.0 (135) / 0 * 3.5 (240) / 0 5.6 (385) / 0 – / 0 – / 0
200 8" PTFE / PFA
2.9 (200) / 0 * 4.2 (290) / 0 5.9 (410) / 0 – / 0 – / 0
250 10" PTFE
4.8 (330) * 5.8 (400) 7.7 (530) – –
300 12" PTFE
5.8 (400) * 7.3 (500) 9.1 (630) – –
350 14" PTFE
6.8 (470) * 8.7 (600) 10.6 (730) – –
400 16" PTFE
7.8 (540) * 9.7 (670) 11.6 (800) – –
450 18" PTFE
Partial vacuum is impermissible500 20" PTFE
600 24" PTFE
* No value can be quoted.
Promag H
Nominal diameter
Measuring
tube lining
Resistance of measuring tube lining to partial vacuum
Limit values for abs. pressure [psia] at various fluid temperatures
[mm] [inch] 77°F
(25°C)
176°F
(80°C)
212°F
(100°C)
266°F
(130°C)
302°F
(150°C)
356°F
(180°C)
2 - 1001/12 - 4"PFA 000000