SS2100i-1 Gas Analyzer
iv 4900002224 rev. E 12-18-20
Figure A–1. Outline and mounting diagram . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Figure B–1. Measurement cell types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
Figure B–2. Stainless steel mirror marking . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
Figure B–3. Electronics assembly panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
Figure B–4. Lowered top-level electronics assembly exposing the
sample panel assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
Figure B–5. Optical head cable connection . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
Figure B–6. Stainless steel mirror; mirror side up . . . . . . . . . . . . . . . . . . . . B-12
Figure B–7. Cell cabinet interior (lower level) with 28 m cell . . . . . . . . . . . . . B-15
Figure B–8. Removing the screw from the harness cap . . . . . . . . . . . . . . . . . B-15
Figure B–9. Removing the harness cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-16
Figure B–10. Removing the pressure sensor . . . . . . . . . . . . . . . . . . . . . . . . . B-16
Figure B–11. Replacing seal tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-17
Figure B–12. New pressure sensor installed . . . . . . . . . . . . . . . . . . . . . . . . . B-18
Figure B–13. Unpacking enclosure insulation. . . . . . . . . . . . . . . . . . . . . . . . . B-20
Figure B–14. Flame arrestor positions inside enclosure. . . . . . . . . . . . . . . . . . B-20
Figure B–15. Removing the flame arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . B-21
Figure C–1. Electronics panel assembly parts . . . . . . . . . . . . . . . . . . . . . . . . C-2
Figure C–2. Electronics panel assembly parts (Continued). . . . . . . . . . . . . . . . C-3
Figure C–3. Electronics panel assembly parts (Continued). . . . . . . . . . . . . . . . C-4
Figure C–4. Field interface terminal block assembly . . . . . . . . . . . . . . . . . . . . C-6
Figure C–5. 8/28 m sample cell panel assembly parts . . . . . . . . . . . . . . . . . . C-8
Figure C–6. 8/28 m sample cell panel assembly parts (Continued). . . . . . . . . . C-9
Figure C–7. 0.8 m sample cell panel assembly parts. . . . . . . . . . . . . . . . . . . C-11
Figure C–8. 0.1 m sample cell panel assembly parts. . . . . . . . . . . . . . . . . . . C-13
Figure C–9. 0.1 m sample cell panel assembly parts (Continued). . . . . . . . . . C-14
Figure C–10. Analyzer enclosure assembly parts . . . . . . . . . . . . . . . . . . . . . . C-15
Figure D–1. Wiring schematic of SS2100i-1 electronics power systems . . . . . . . D-1
Figure D–2. Wiring schematic of SS2100i-1 heater system . . . . . . . . . . . . . . . D-2
Figure D–3. Wiring schematic of SS2100i-1 digital I/O . . . . . . . . . . . . . . . . . . D-3
Figure D–4. Wiring schematic of SS2100i-1 alarms . . . . . . . . . . . . . . . . . . . . D-4
Figure D–5. Wiring schematic of SS2100i-1 serial and Ethernet signals. . . . . . . D-5
Figure D–6. Wiring schematic of SS2100i-1 inter-card connections . . . . . . . . . D-6
Figure D–7. Wiring schematic of SS2100i-1 sample cell connections. . . . . . . . . D-7
Figure D–8. Wiring schematic of SS2100i-1 sample cell connections
(Continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-8
To Next Page
Loading...
Need help?
General
