Fargo DTC400 - Page 339

RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC400 Card Printer/Encoder User Guide (Rev. 2.2) 4
inches or mm option, 6-6
incorrect image darkness problems, 4-44
increase Printhead heat, 6-92
Input, 14-10
Input Hopper, 14-10
integral resistor, 7-2
Interface, 2-3
Intermediate Transfer Media (InTM), 14-10
internal electrical components, 7-2
internal Printer settings, 6-31
ISO, 14-10
ISO 7811-2 Magnetic Stripe, 6-46
ISO encoded data format, 6-39
ISO Standard selections, 6-44
ISO Standard settings, 6-37
ISO Track Locations, 6-46
J
JIS II (Japanese Industrial Standard), 14-10
K
K Panel, 14-10
K Panel Resin options, 6-62, 6-86
K Panel Resin tab, 6-76
L
Lamination, 14-10
Lamination Drive, 9-2
Lamination Drive Stepper, 9-2
Lamination Roller Lift, 9-2
Lamination Sensor Calibration, 4-54
LAN (Local Area Network), 14-10
Landscape, 14-11
Landscape orientation, 6-32
LCD (Liquid Crystal Display), 14-11
LED (Light Emitting Diode), 14-11
less heat / more heat, 6-28, 6-29
LoCo (Low Coercivity), 14-11
LPT Port (Line Printer Port), 14-11
LRC Generation, 6-44
LRC Generation Mode, 6-44
M
magnetic data, 6-99
Magnetic Encoder, 4-18
Magnetic encoding, 14-11
Magnetic Offset option, 6-99
Magnetic Offset value, 6-99
Magnetic stripe, 14-11
, 4-15
Magnetic Stripe Encoding Module, 6-36
Magnetic Stripe reader, 4-15
Magnetic Track, 14-11
Magnetic Track Options, 6-37
Magnetic Track Selection, 6-37, 6-38
Magnetic Track Selection option, 6-37
Magnetic Verify, 14-11
maximum adjustment range, 6-94, 6-99
MB (Megabyte), 14-12
Media, 14-11
Memory, 2-3, 14-12
Menu, 14-12
Metallic Resin, 2-10
Monitor, 6-19
Monochrome, 14-12
Monochrome Dye-Sub (B), 4-54
Monochrome Resin (K), 4-54
Motor Voltages (when active), 9-2
Multi-Language Extension (MLE), 6-42
N
Network, 14-12
None, 6-19
O
Oersted (Oe), 14-12
Offset, 14-12
Omit Signature Area setting, 6-59
On LED, 4-54, 4-55
onscreen card design, 6-82
Operating Temperature, 2-3
optional Magnetic Stripe Encoding Module, 6-36
O-Ring, 14-12
OS (Operating System), 14-12
Output, 14-12
Output Hopper, 14-12
Overlaminate, 14-13
Overlay, 14-12
Overlay / Print Area, 6-59, 6-60
Overlay / Print Area options, 6-56
Overlay / Print Area tab, 6-50
Oversized Cards, 14-13
P
Parallel, 14-13
Parallel port, 14-13
Pause button and LED, 2-8
Pause/Resume button, 4-54, 4-55
PC (Personal Computer), 14-13
PCB (Printed Circuit Board), 14-13
Peel, 14-13
Peel-Off, 14-13
Peripheral, 14-13
PET, 14-14
Photo, 6-20
Pinch Roller, 14-14
Pixel, 14-14
, 4-41
Platen, 14-14
PolyGuard Overlaminate, 14-14
poor image quality problems, 4-51, 4-52
Port, 14-14
Portrait, 14-14
Portrait or Landscape, 6-7
Portrait, Landscape, or Rotate 180 Degrees, 6-32
positive / negative Print Length value, 6-94