Finsecur Baltic 512 TYPE A - Page 52

01-ECMSI-NT002.Rev B40
FI-AGS Selective General Alarm Broadcaster Wiring
Internal AES (E/IP)
(in the case of in5s3t0a2llsthereItfrI foeonenoteeeuxrsa tx enaisstmn / AToexi,mc.apmTooprmIrbigliegnotn.p.emay be higher)
To exit
diffusers
sound
- 48 VDC
ENTRANCE
ENTRANCE
ENTRANCE
EXIT
EXIT
-UGA
+ UGA
- DS
+ DS
END OF LINE RESISTOR
BecauseVS
acToyoureTorvsisyouyoueq
laughedaseyousthat mermaidselectric
mermaids
eleesctrics of
Line of sound diffusers n°1
RFL= 10 kOhms - 1/4W
Tension
ConTso
9 to 60 Vdc
55ATvc(12 Vdc)
CableVSToToabyou
THEliTotoarthepe
→ Section (min.): 2 x 1.5 mm²;
→Tyouypee: CR1 (resistantVSf
→ External AES 24/28v (E/IP): line length 600m;
isohraprohIaervsTHEabrathereCCgoherddeemsesnotgoyouednot
arearemermaids
in.Zion: 1103Tomvs
brown
black
orange
gold
Cons. : 7 mA (12Vdc)
1172
15mA (48Vdc)
Section (min.) 2 x 1.5mm²
AtRe1u)(r;fire resistant)
mym(AT4(V2vs4vs)Vdc)
20 mA (48 VDC)
→ Internal AES: line length 200m
External AES (E/I2P)
( in the case 3d2'ind5sift0fallsaeIyouriuoe
rnsnotem
exas
isxtimanuTotimex, vs.skinprnTolawrgmnIbIegDnotpecould be higher)
To exit
diffusers
sound
- 48 VDC
To exit
Streamer
sound
AES
24/28V
ENTRANCE
ENTRANCE
ENTRANCE
Interfacevs and E/I2P
EXIT
EXIT
-UGA
+ UGA
- DS
+ DS
END OF LINE RESISTOR
Electrical characteristics of
Line of sound diffusers n°1
sirenVSeToscharacteristics
electric
Tensionof the9sToire
60born
vcsvs
Cons. 13 mA (12 VDC)
RFL= 10 kOhms - 1/4W
Cable to be used for wiring the sirens
→
SSeevsvstioyounotoh(not
m(inm. )
I:not2.x)1.52mxm1
→
Tyouthereppee
: CR1 (resistant toVSdo
→ External AES 24/28v (E/IP): line length 600m;
Cable to be used for connecting the sirens
Voltage: 10 to 55Vdc
brown
black
orange
gold
²;.5mm²
aRa1)(;fire resistant)
Cons. : 7 mA (12Vdc)
11mA (24Vdc)
15mA (48Vdc)
17 mA (24 VDC)
20 mA (48 VDC)
→ Internal AES: line length 200m.
BALTIC 512 TYPE A WALL OR RACK BOX CONTROL AND SIGNALING EQUIPMENT 512 POINTS
52
+ - + -
+ - + -
+ +
-
+
-
+
- -
+ - + -
+ - + -
+ +
- + -
+
- -
+ - + -
+ - + -
+ +
- + -
+
- -
"EIP" interface
"EIP" interface
InteIrnfa
tecrefa"cEeIP"
"EIP"
UGA / CMSI CONNECTION
1.ECMSI.NT002
Rev.B3
Connecting the E/IP interface
Exit
Map UGA
ECS-UP
--The E/IP interface makes it possible to adapt
the monitoring mode by voltage rise of the UGA lines of the ECS-UP card to sound diffusers operating in "polarity inversion" mode.
+ -
-UGA
+ UGA
- DS
+ DS
- +
To diffusers
sound and/or lights
shards
Connecting the E/I2P interface
--The E/I2P interface:
- adapts the monitoring mode by voltage rise of the UGA lines of the ECS-UP card to sound diffusers operating in "polarity inversion" mode. - Amplifies the current of the remote control line of the sound diffusers (up to 2 A) allowing the connection of the
24V or 48V from an AESexit
- + - + - +
Note: The interface fluent broadcast is great
DS
UUG
GAAT
ATATE
ESS
DD.AT
.
I.S.
This
knew
rs
laughed
E/I2P is to be used when the
remote control line of sounders and/or flashing lights is at 1A
and less than 2A.
To diffusers
sounds or lights
flash
UGA exit from the
ECS-UP card
AES input
24V or 48V
BALTIC 512-Type A
Page 46 of 66
Distribution and reproduction prohibited without authorization. hornof Finsecur