gefran TPD32-EV-500 series - 3 - INSTALLATION GUIDELINES; 3.3 MOUNTING THE DEVICE; 4 - WIRING PROCEDURE; 4.2 WIRING THE DRIVE

—————— TPD32-EV ——————
4
Figure 2.4.17: TPD32-EV-500/520-2700-4B-E dimensions.................................................................................................................................. 53
Figure 2.4.18: TPD32-EV-500/520-3300-4B-E and TPD32-EV-690/720-3300-4B-E dimensions .......................................................................... 54
Figure 2.4.19: TPD32-EV-690/720-2400...2700-4B-E dimensions....................................................................................................................... 55
2.5 WATT LOSS ........................................................................................................................................... 56
Table 2.5.1: Dissipated power TPD32-EV and TPD32-EV-FC series ..................................................................................................................... 56
Table 2.5.2: Dissipated power TPD32-EV-CU series ............................................................................................................................................ 57
2.6 MOTORS, ENCODER, TACHOMETER ................................................................................................. 58
2.6.1 Motors ............................................................................................................................................................................58
2.6.2 Encoder / Tachometer ....................................................................................................................................................59
3 - INSTALLATION GUIDELINES .....................................................................................60
3.1 PERMISSIBLE AMBIENT CONDITION ................................................................................................. 60
3.2 DISPOSAL OF THE DEVICE ................................................................................................................. 61
3.3 MOUNTING THE DEVICE ..................................................................................................................... 61
Figure 3.3.1: max Angle of Inclination ................................................................................................................................................................. 61
Figure 3.3.2: Mounting Clearance ....................................................................................................................................................................... 62
4. WIRING PROCEDURE .................................................................................................63
4.1 REMOVING THE FRONT COVER ........................................................................................................ 63
Figure 4.1.1: Removing the Front Panel .............................................................................................................................................................. 63
Terminal Assignments/Cable Sections ................................................................................................................................................. 63
4.2 WIRING THE DRIVE .............................................................................................................................. 64
4.3 POWER SECTION ................................................................................................................................. 64
Table 4.3.1: Terminals description ....................................................................................................................................................................... 64
Table 4.3.2: Cable size for power terminals U, V, W, C, D, PE .............................................................................................................................. 64
Table 4.3.3: Cable section for UL approval ......................................................................................................................................................... 65
Table 4.3.4: Wire adapter Kit and lugs suggested for UL approval ...................................................................................................................... 66
Table 4.3.5: Wire adapter Kit and lugs suggested for UL approval ...................................................................................................................... 67
Table 4.3.6: Cable size for power field terminals U1, V1, C1, D1 ........................................................................................................................ 68
Table 4.3.7: Cable size for fans, signals, thermistors and regulation supply ........................................................................................................ 68
4.4 REGULATION SECTION ...................................................................................................................... 69
4.4.1 R-TPD32-EV Regulation Card .......................................................................................................................................69
Figure 4.4.1: R-TPD32-EV regulation card .......................................................................................................................................................... 69
Table 4.4.1: LEDs on the R-TPD32-EV card ......................................................................................................................................................... 69
Table 4.4.2-A: Dip-switch S15 adaptation of the regulation card to the device type ........................................................................................... 70
Table 4.4.2-B: Dip-switch S15 Adjustment of the TPD32-EV-CU-... series mains voltage regulation card ............................................................ 71
Table 4.4.3: Dip-switch S4 adaptation of the tachometer feedback to the input voltage ................................................................................... 72
Table 4.4.4: Jumpers on the Regulator card ........................................................................................................................................................ 72
Table 4.4.5: Test points on Regulator card ........................................................................................................................................................... 72
Figure 4.4.2: Disposition of terminals from 1 to 42 .............................................................................................................................................. 72
Table 4.4.6 - A: Terminal Assignment (terminals from 1 to 20) ............................................................................................................................ 73
Table 4.4.6 - B: Terminal Assignment (terminals from 21 to 42) ......................................................................................................................... 73
Table 4.4.7: Cable size for fans, signals, and thermistors ................................................................................................................................... 74
Table 4.4.8: Terminal strip for the connection of an analog tachometer .............................................................................................................. 75
Table 4.4.9: Assignment of an XE1 connector for a sinusoidal encoder .............................................................................................................. 75
Table 4.4.10: Assignment of the XE2 connector for a digital encoder ................................................................................................................. 75
4.5 RS485 SERIAL INTERFACE ................................................................................................................. 76
4.5.1 Description .....................................................................................................................................................................76
Figure 4.5.1.1: RS485 serial interface ................................................................................................................................................................. 76
4.5.2 RS485 serial interface connector description ................................................................................................................77
Table 4.5.2.1: Description of the XS connector for the RS485 serial interface .................................................................................................... 77
4.6 INPUT/OUTPUT EXPANSION CARD TBO ............................................................................................ 77
4.6.1 Assignment of the plug-in terminal strip (terminals 1...15) for Option Card TBO ........................................................................ 78
Table 4.6.1.1: Terminal strip connections ............................................................................................................................................................ 78
Table 4.6.1.2: Cable size for terminals of the option card TBO ............................................................................................................................ 78