EasyManua.ls Logo

Generic Onyx 50 User Manual

Generic Onyx 50
173 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Service Manual
Holtvej 8-10, Høruphav, 6470 Sydals
Telefon: +45 73 15 11 00
Fax: +45 73 15 11 01
info@scanmi.dk · www.scanmi.dk
CVR: 27 73 31 07
www.genericmotor.dk
Juli 2011
ONYX
50

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Generic Onyx 50 and is the answer not in the manual?

Generic Onyx 50 Specifications

General IconGeneral
BrandGeneric
ModelOnyx 50
CategoryScooter
LanguageEnglish

Summary

Battery/Charging System

1.2 Failure Diagnosis

Troubleshooting guide for power supply issues like dead battery, fuse blow, and low voltage.

1.3 Battery

Procedures for removing, inspecting charging state, and charging the motorcycle battery.

Ignition System

2.2 Failure Diagnosis

Troubleshooting for spark plug issues, low/high voltage, and charging coil problems.

Activation System

3.2 Failure Diagnosis

Troubleshooting for activation failures like weak rotation or non-rotating starting motor.

Brake System

5.2 Failure Diagnosis

Troubleshooting for poor braking performance, slow reaction, and abnormal noises.

5.3 Front Fluid Brake

Detailed steps for removing, checking, and installing the front fluid brake system.

5.4 Rear Drum Brake

Procedures for removing, checking, and installing the rear drum brake system.

Front Wheel and Front Suspension

7.2 Failure Diagnosis

Troubleshooting for steering difficulties, unsteady steering, front wheel shimmy, and shock absorber noise.

7.3 Front Wheel

Steps for removing, checking (axle, rim, bearing), and installing the front wheel.

7.5 Front Fork

Detailed instructions for removing, installing, and checking the front fork.

Rear Wheel and Rear Suspension

8.3 Rear Wheel

Steps for removing, inspecting (rim swinging), and installing the rear wheel.

8.4 Rear Shock Absorber

Instructions for removing, inspecting, adjusting, and installing the rear shock absorber.

Removal and Installation of Motor

10.2 Failure Diagnosis

Troubleshooting for motor issues like swinging or loose driving devices.

10.3 Removal of Motor

Detailed steps for removing the motor and its suspension components.

10.4 Installation of Motor

Instructions for installing the motor, including torque values for mounting.

Carburetor

12.2 Failure Diagnosis

Troubleshooting for starting disorders, excessive fuel, and air mixture issues.

12.3 Removal of Carburetor

Steps for removing the carburetor, including fuel lines and throttle cable.

Cylinder Cap

13.2 Failure Diagnosis

Troubleshooting for gas leakage or high combustion pressure between cylinder cap and body.

Cylinder Body and Piston

14.2 Failure Diagnosis

Troubleshooting for low compression pressure and white smoke from the vent pipe.

14.4 Piston

Procedures for removing and inspecting the piston, piston pin, and piston rings.

14.5 Installation of Piston

Instructions for installing the piston, piston pin, and piston rings.

Driving Disc/Clutch/Driven Wheel/Foot Driving Device

15.2 Failure Diagnosis

Troubleshooting for motor failures, low horsepower, and shaking driving.

15.6 Detach Clutch and Driven Wheel

Instructions for detaching the clutch and driven wheel using a spring compressor.

Crankcase

17.3 Crankcase

Steps for removing, inspecting, and disassembling the crankcase.

Exhaust Gas Discharge Control System

18.5 Solution for Idle Discharge Value Exceeding Defined Value (Two-stroke)

Flowchart for resolving issues with idle discharge values exceeding standards.

Related product manuals