HITEC OPTIC 6 - Glossary

For more information - www.modelflight.com.au
GLOSSAR
Y
The abbreviations used with the Optic are defined below alphabetically.
Related
pages are given in parenthesis following the definition.
A
A
CGL Acrobatic/Glider aircraft menu (15)
A
DIF Aileron differential. Ailerons move more to one
side
than other (31)
A
ILV Differential elevator servos, for 3-D aerobatics (39)
A
TL Adjustable Travel Limit. Limits throttle trims to
only the throttle idle position. (built in to your system)
A
->R Aileron Rudder mixing (36)
C
CAMB A function which droops or raises the entire
trailing
edge of a wing. (32)
COPY Data copy: command used to copy one memory
to
another (11)
CROW Airbrake function (37)
CURSOR Button used to step through menus (9)
D
D/R Dual rate: switch-controlled function reduces
control
travels. (27)
DATA Editing keys change numbers (9)
E
ELVN Elevon function combines ailerons & elevators for
tailless
models. (34)
EPA End Point Adjust. Function that adjusts the servo t
ravel
at the left and right sides. (27)
EXP Exponential function, reduces sensitivity around
neutral
(28)
E->F Elevator Flap mixing (36)
F
FAIL Failsafe function moves servos to preset locations
if
interference is received. (41)
FLPN Flaperon function gives the ailerons a flap
function.
(30)
FLPT Flap travel function. (30)
G
Gear Landing gear control switch. (8)
GYRO
Gyro setting menu (51)
H
HELI Helicopter settings menu. (45)
HOLD Throttle hold function holds the throttle in a near-
idle
position (used for autorotation). (51)
I
INH Inhibit. Function will not operate
L
L/U Indicates Left or Up stick motion
LAND Landing function (33)
Lock
Lock throttle button (9)
M
MAS Master channel in mixer (38)
M.SEL
Model select menu (11)
N
NOR Normal helicopter swashplate (1 servo each for
elevator,
aileron, pitch. (12)
O
OFF Function or Switch in OFF position.
ON
Function or Switch in ON position.
P
PPM Pulse-Position Modulation,
also
known as "FM". (14)
PCM Pulse-Code Modulation. (14)
PMX Programmable mixer. Mixing between
arbitrary
channels. (38)
PTCV Pitch curve function (53)
Q
QPCM Pulse-Code Modulation. (14)
R
R/D Indicates Right or Down stick motion
R
EV Reverse. Servo operating direction
switching
function. (29)
REST Reset model memory (15)
RVMX
Revolution mixing (54)
R->T Rudder Throttle mixing (50)
S
S/W SEL Select on-off switches for different functions (39,53)
SFT.N
Negative transmit shift direction (13)
SFT.P Positive transmit shift direction (13)
SLV
Slave channel in program mixer (38)
STCK
Choose Mode of transmitter. (13)
STRM
Subtrim function used to adjust
servo neutrals. (28)
SWAH
Swash type (12,54)
T
T.CUT Throttle cut function used to kill engine
without
moving trims (29)
THCV Throttle curve function (52)
TIME
Timer/Stopwatch function (14)
V
VTAL V-tail function combines the
elevators
and rudder. (35)
Numerical
120' Helicopter swashplate, 120 ° (12,54)
GLOSSAR
Y
-
Pa
g
e 5
7