HP integrity rx2800 i4 User Manual

Both Boxboro and ICH have an IOxAPIC, and both are used for the PCI devices underneath
Boxboro. The ICH’s IOxAPIC range begins at 0xFEC00000, and Boxboro’s begins at
0xFEC40000.
6. Hides unused devices from the OS by setting the appropriate ICH registers.
Customer messaging policy
• See the SEL for any action from low level I/O subsystem faults, because the System Insight
Display may not have any illuminated LEDs.
• For configuration-type errors, for example, no iLO 3 MP or core I/O HBAs installed or working,
see “Supported configurations” (page 75) for actions.
• Some diagnostic messages are reported for high level I/O subsystem errors. All fatal I/O
subsystem errors cause global MCAs.
Table 36 I/O subsystem events that light SID LEDs
NotesSourceCauseSample IPMI eventsDiagnostic
LEDs
Likely a short on
I/O card or I/O
slot.
iLO MPOver-current on PCI slotType 02h, 03h:05h:01h
CURRENT_LIMIT_EXCEEDED
I/O Card
A voltage on the
I/O riser is out of
iLO MPVoltage on CRU is
inadequate
Type 02h, 02h:07h:03h
VOLTAGE_DEGRADES_TO_NON_RECOVERABLE
I/O Riser
range (likely too
low)
A voltage on the
disk backplane is
iLO MPVoltage on CRU is
inadequate
Type 02h, 02h:07h:03h
VOLTAGE_DEGRADES_TO_NON_RECOVERABLE
Disk Backplane
out of range
(likely too low)
Table 37 I/O card events that might illuminate SID LEDs
NotesSourceCauseSample IPMI EventsDiagnostic
LEDs
Disallow O/S
boot and display
SFWA non hot plug I/O slot
power consumption
Type E0h, 4658d:26d
IO_PCI_POWER_OVERLOAD_ERR
I/O Card
the followingincreases the total I/O
UEFI errorpower consumption
message, "I/Obeyond the supported
limit configuration
exceed"
Display UEFI
warning message
SFWInsufficient power to
power on a hot-plug
PCI-X slot
Type E0h, 137d:26d
IO_NOT_ENOUGH_POWER_ERROR
I/O Card
"Failed I/O slots
deconfigured"
Either a card /
slot issue. Re-seat
card first.
SFWPCI slot standby power
failed
Type E0h, 147d:26d
IO_SLOT_STANDBY_POWER_ERROR
I/O Card
Either a card /
slot issue. Re-seat
card first.
SFWPCI-X hot-plug controller
failed
Type E0h, 131d:26d
IO_HOT_PLUG_CTRL_FAILED
I/O Card
Remove any
unsupported I/O
SFWPCI bus walk (I/O
discovery) resources
exceeded
Type E0h, 139d:26d
IO_PCI_MAPPING_TOO_BIG
I/O Card
cards. Move I/O
card to an
unused PCI slot
HP Confidential86 Troubleshooting

HP integrity rx2800 i4 Specifications

General

Number of Processors	1 or 2
Memory Slots	24 DIMM slots
Processor Cores	4 or 8 per processor
Cache	32 MB L3 per processor
Memory	Up to 384 GB DDR3
Storage	Up to 8 SFF SAS/SATA drives
RAID Support	RAID 0, 1, 5, 6
Network	Integrated 10/100/1000Base-T Ethernet
Network Controller	HP NC382i
Expansion Slots	6 PCIe 2.0 slots
Power Supply	Hot-plug redundant power supplies
Operating Systems	HP-UX, Linux
Form Factor	2U Rack
Processor Speed	1.73 GHz, 2.13 GHz, or 2.53 GHz