Hydro Mobile F200 User Manual (English)

To Next Page

Owner’s Manual

Call us for information:

1-888-484-9376 (US)

(toll free in the United States)

(450) 589-8100 (Canada)

21053002-0-00000-0

F2_OpMan_v2.02_EN

for gas-powered and electrical

unit models F200 and F300

Table of Contents3
Introduction4
Warranty5
Performance and Safety Rules6
- Motorized Unit Overview9
List of Components Included with Shipped Unit10
Toolbox Components10
Motorized Unit Speciﬁ Cations11
- Fi G. 1.1011
- Fi G. 1.1312
Weight of Components13
- Mast Guards13
- Mast Head13
- Link Bridge Guardrails13
- Fi G. 1.1713
- Description13
Dimensions14
- Minimum Bearing Surface Capacities15
- Recommended Cribbing15
Setup and Conﬁ Gurations General Guidelines16
- Combination of Equipment and Accessories16
  - Restriction of Equipment and Accessories Allowed on each Cantilever Side of an Unlinked Conﬁ Guration (Single or Multiple Units)17
  - Restriction of Equipment and Accessories Allowed on each Bearing Bridge of an Unlinked Conﬁ Guration17
- Deﬁ Nition of a Standard Conﬁ Guration19
- Methods of Installation19
- Splitting a Motorized Unit (F300 Unit Model Only)33
- Dismantling an Installation35
Emergency Descent Control System42
- Procedure for a Single Unit Installation42
- Procedure for a Multiple Units Installation43
Overspeed Safety Device45
Inclinometer45
- Connection45
- Detection of a ± 2-Degree Slope46
- Detection of a ± 5-Degree Slope46
- Adjustment of the 0° Level Position46
- Testing the Inclinometer47
- Veriﬁ Cation of Limit Switches and Panel Alerts47
Fall Protection48
- Bridges49
Standard Bridge49
- Installation of a Bridge49
- Storage of a Bridge49
Bridge Types50
Cantilever51
Bearing Bridge51
- Safety Guidelines51
- Assembly of a Bearing Bridge Structure51
- Installation of a Twin Mast Adapter51
- Installation of the Bearing Bridge Structure52
- Dismantling a Bearing Bridge Structure52
Forward Extension Bridge53
Bridge Deck Extension54
Swivel Bridge55
- Installation55
- Angle Adjustment55
- Installation of Swivel Bridge Guardrails56
- Front Cantilever Conﬁ Gurations57
- Back Cantilever Conﬁ Gurations58
- Front Bearing Bridge Conﬁ Gurations60
- Back Bearing Bridge Conﬁ Gurations62
- Counterweight Adapter64
- Outrigger Support Assembly66
  - Power Pack and Components68
Gas-Powered Unit68
- Startup Preparation Instructions68
- Motorized Unit Startup Procedure69
- Engine Shutdown Procedure69
Electrical Unit70
- Startup Preparation Instructions70
- Power Cable Selection Chart71
- Motorized Unit Startup Procedure72
- Motorized Unit Shutdown Procedure72
  - Control Panel73
Description74
Controls74
Screen Alerts and Instructions75
- Unlocking the Display Screen75
- Main Menu Screen75
- F1 - Status Info76
- F2 - Alerts76
- F3 - Inputs and Outputs81
- F4 - Conﬁ Guration82
Mast Sections83
- Installation83
- Loading Mast Sections on the Platform84
- Removal and Transport of Mast Sections84
Mast Ties84
- General Guidelines84
- Installation of Standard Mast Ties85
- Mast Tie Schedules85
- Location of Perpendicular Mast Ties87
- Recommended Order of Installation87
- Methods of Installation of Tie Levels88
- Installation of Mast Ties with Extensions88
- Additional Rigid Dual Clamps88
- Mast Tie Requirements for Plank Conﬁ Gurations89
- Wind Speeds89
- Removal of Mast Ties90
Anchoring System90
- Installation of Wall Ties90
- Wall Tie Reactions91
- Wall Tie Types91
- Wall Tie Distance for Vertical Anchoring Installation91
Load Capacity Calculation Guidelines93
Calculating the Maximum Number of Workers for an Installation93
- Linked Conﬁ Gurations Single Unit Installation94
- Multiple Units Installation95
- Multiple Units Installation97
Unlinked Conﬁ Gurations98
Forward Extension Installation Using a Standard Bridge98
- Using a Multi Purpose Bridge98
Swivel Bridge Installation98
- Single Unit (90 Degrees)99
- Multiple Units100
- With Counterweight Adapter - Three Bridges101
- With Counterweight Adapter - Two Bridges102
Hoist Installation Single Unit Setup103
- Multiple Units Setup104
Cantilever Reinforcement Cable Retainer Installations Single Unit Installation105
- Multiple Units Installation106
Safety Accessories107
- Guardrails107
Access Stairs109
Bridge Installation Support Brackets109
Outriggers110
- Planking Conﬁ Gurations110
  - Outrigger Selection Table110
  - Planking Conﬁ Guration Guidelines110
- Doubled Outriggers111
  - Outriggers Required for Doubling111
- Cross Boxes112
- Non Standard Planking Conﬁ Gurations112
- Outriggers - Top Position114
- Outriggers - Bottom Position114
Multiple Mast Handler115
Adapter Base for Freestanding Installation116
- Installation of the Adapter Base116
- Installation of the Motorized Unit on the Adapter Base116
- Authorized Height for Freestanding Installation with Adapter Base117
Jib Arm118
- Installation of the Jib Arm on the Motorized Unit118
- Using the Jib Arm to Lift a Mast Section119
- Maximizing the Use of a Single Jib Arm119
Hoist Support Assembly120
Monorail121
Weather Protection for Bridges122
Cantilever Reinforcement Cable Retainer123
Adapter Base for Sidewalk Canopy Installation125
- Installation of the Adapter Base125
- Minimum Bearing Surface Capacities for an Installation with a Sidewalk Canopy125
- Calculating Distance from Wall126
- Installation of the Motorized Unit on the Adapter Base127
- Dismantling Guidelines127
Hydraulic Oil Heater / Recirculator128
Transport and Storage129
- Preparation of the Motorized Unit129
- Lifting and Moving a Motorized Unit or a Setup130
  - Using the Forklift Pockets on the Mast Head130
  - Using the Shackle on the Mast Head130
- Storage of a Motorized Unit130
- Storage of a Bridge131
- Storage of Mast Sections131
- Greasing of Gears and Racks132
- Inspections133
- Samples of Checklist135

Need help?

Do you have a question about the Hydro Mobile F200 and is the answer not in the manual?

Hydro Mobile F200 Specifications

General

Brand	Hydro Mobile
Model	F200
Category	Lifting Systems
Language	English

Hydro Mobile F200 User Manual

Table of Contents

Hydro Mobile F200 Specifications