EasyManua.ls Logo

Icom IC-7600 - Page 14

Icom IC-7600
196 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
!4 NOISE REDUCTION SWITCH [NR] (p. 90)
Push to switch DSP noise reduction ON or OFF.
The indicator on this switch lights green when the
function is activated.
!5 NOISE REDUCTION LEVEL CONTROL [NR]
(outer control; p. 90)
Adjusts the DSP noise reduction level when the
noise reduction function is in use. Set for maximum
readability.
• To use this control, push [NR] (!4) in advance.
Decreases
Increases
!6 MONITOR SWITCH [MONITOR] (p. 95)
Push to monitor your transmitted signal.
The CW sidetone functions regardless of the
[MONITOR] switch setting in the CW mode.
The indicator on this switch lights green while the
function is activated.
!7 ANTENNA TUNER SWITCH [TUNER] (p. 121)
Turns the internal antenna tuner ON or OFF
(bypass) when pushed momentarily.
The indicator on this switch lights green when the
tuner is turned ON, goes off when tuner is turned
OFF (bypassed).
Allows you to tune the antenna tuner manually,
when held down for 1 second.
The indicator on this switch blinks red during
manual tuning.
When the tuner cannot tune the antenna, the tuning
circuit is automatically bypassed after 20 seconds.
!8 BALANCE CONTROL [BAL] (inner control; p. 87)
Adjusts the audio output balance between main
and sub readout frequencies while in dualwatch.
Increases main
readout gain
Increases sub
readout gain
!9 NOISE BLANKER SWITCH [NB] (p. 89)
Switches the noise blanker ON or OFF when
pushed. The noise blanker reduces pulse-type
noise such as that generated by automobile
ignition systems. This function cannot be used in
the FM mode, and is not effective for non-pulse-
type noise.
The indicator on this switch lights green while the
function is activated.
Selects the noise blanker level set mode when
held down for 1 second.
@0 LCD FUNCTION SWITCHES [F-1] to [F-6]
Push to select the function indicated in the LCD
display above these switches.
Functions vary, depending on the operating condition.
Front panel (continued)
TWIN
-
PBT
RIT/ TX
Ӡ
NOTCH
CW PITCH
VOICE MEMORY
BAL NR
AF RF/SQL
MIC GAIN RF POWER BK
-
IN DELAYKEY SPEED
TIMER
PHONES
ELEC
-
KEY
MIC
AUTO
TUNE
GENEF
-
INP
1. 83.5
12
14
5
18
6
7
3
24
8
28
9
50
0
ENT
4
7
10
21
CHANGE
TS
XFC
SPLIT
DUAL
WATCH
MAIN
/
SUB
M.SCOPE
VFO/MEMO
MP
-
W
MW
MP
-
R
F
-
6
F
-
5
F
-
4
F
-
3
F
-
2
F
-
1
NRNB
PBT
-
CLR
APF/TPF
NOTCH
POWER
RIT
CLEAR
TX
Ӡ
SPEECH
LOCK
FILTER
RECPLAY
EXIT
/
SET
SSBCW
RTTY
/
PSK
AM/FM
MONITOR
TRANSMIT
TUNER
HF/50MHz TRANSCEIVER
LOCKTX RX SPLIT
!4!5!6!7
!9
!8
@0 @1 @2 @3 @7 @8 @9@6@5@4
5
1
PANEL DESCRIPTION

Table of Contents

Other manuals for Icom IC-7600

Related product manuals