#0 TRANSMIT INDICATOR [TX]
Lights red while transmitting.
#1 RECEIVE INDICATOR [RX]
Lights green while receiving a signal and when the
squelch is open.
#2 LCD FUNCTION DISPLAY (p. 13)
Shows the operating frequency, function switch
menus, spectrum scope screen, memory list
screen, set mode settings, etc.
#3 SPLIT OPERATION INDICATOR [SPLIT] (p. 96)
Lights during split frequency operation.
#4 MAIN/SUB CHANGE SWITCH [CHANGE]
➥ Switches the frequency and selected memory
channel between main and sub readouts when
pushed.
• Switches between transmit frequency and receive
frequency when the split frequency function is ON.
(p. 96)
➥ Equalizes the sub readout frequency to the
main readout frequency when held down for 1
second.
#5 LOCK INDICATOR [LOCK] (p. 90)
Lights when the dial lock function is activated.
#6 DUALWATCH SWITCH [DUALWATCH] (p. 87)
➥ Push to turn the dualwatch function ON or OFF.
• “ ” appears when the dualwatch function
ON.
➥ Hold down for 1 second to turn the dualwatch
function ON and equalize the sub readout
frequency to the main readout. (Quick dualwatch
function)
• The quick dualwatch function can be turned OFF in
the Others set mode. (p. 137)
#7 SPLIT SWITCH [SPLIT] (p. 96)
➥ Push to turn the split function ON or OFF.
• “ ” appears when the split function is in
use.
➥ Hold down for 1 second to activate the quick
split function.
• Turns the split function ON and equalizes the sub
readout frequency to the main readout and sets
the sub readout for frequency input in the non-FM
modes. (p. 97)
• The offset frequency is shifted from the selected
VFO frequency in the FM mode. (p. 137)
• The tone encoder function is turned ON in the FM
mode.
• The quick split function can be turned OFF in the
Others set mode. (p. 137)
#8 KEYPAD
➥ Pushing a key selects the operating band. (p. 29)
• [GEN •] selects the general coverage band.
➥ Pushing the same key 2 or 3 times calls up
other stacked frequencies in the band.
(p. 29)
• Icom’s triple band stacking register memorizes 3
frequencies in each band.
➥ After pushing [F-INP ENT], push a key on the
keypad to enter a numeric frequency. After
entering, push [F-INP ENT] to select the desired
frequency directly
(p. 30)
• For example, to enter 14.195 MHz:
Push [F-INP ENT] [1] [4] [•] [1] [9] [5] [F-INP
ENT].
➥ After pushing [F-INP ENT], push a key on
the keypad to enter a memory channel. After
entering, push [∫] or [√] to directly select the
desired memory channel.
(p. 107)
Front panel (continued) ■
TWIN
-
PBT
RIT/ TX
Ӡ
NOTCH
CW PITCH
VOICE MEMORY
BAL NR
AF RF/SQL
MIC GAIN RF POWER BK
-
IN DELAYKEY SPEED
TIMER
PHONES
ELEC
-
KEY
MIC
AUTO
TUNE
GENEF
-
INP
1. 83.5
12
14
5
18
6
7
3
24
8
28
9
50
0
ENT
4
7
10
21
CHANGE
TS
XFC
SPLIT
DUAL
WATCH
MAIN
/
SUB
M.SCOPE
VFO/MEMO
MP
-
W
MW
MP
-
R
F
-
6
F
-
5
F
-
4
F
-
3
F
-
2
F
-
1
NRNB
PBT
-
CLR
APF/TPF
NOTCH
POWER
RIT
CLEAR
TX
Ӡ
SPEECH
LOCK
FILTER
RECPLAY
EXIT
/
SET
SSBCW
RTTY
/
PSK
AM/FM
MONITOR
TRANSMIT
TUNER
HF/50MHz TRANSCEIVER
LOCKTX RX SPLIT
$2
$3
#0 #5#4 #6 #7 #8 #9
$0
#3#2#1
$1
$4$5
7
1
PANEL DESCRIPTION
To Next Page
Loading...
