Cmd.
Sub
cmd.
Data Description
16 02 00 Preamp OFF
01 Preamp 1 ON
02 Preamp 2 ON
12 00 AGC FAST selection
01 AGC MID selection
02 AGC SLOW selection
22 00 Noise blanker OFF
01 Noise blanker ON
32 00 Audio peak filter OFF
01 Audio peak filter WIDE ON
(320 Hz is selected when SHARP APF is set)
02 Audio peak filter MID ON
(160 Hz is selected when SHARP APF is set)
03 Audio peak filter NAR ON
(80 Hz is selected when SHARP APF is set)
40 00 Noise reduction OFF
01 Noise reduction ON
41 00 Auto notch function OFF
01 Auto notch function ON
42 00 Repeater tone OFF
01 Repeater tone ON
43 00 Tone squelch OFF
01 Tone squelch ON
44 00 Speech compressor OFF
01 Speech compressor ON
45 00 Monitor function OFF
01 Monitor function ON
46 00 VOX function OFF
01 VOX function ON
47 00 BK-IN function OFF
01 Semi BK-IN function ON
02 Full BK-IN function ON
48 00 Manual notch function OFF
01 Manual notch function ON
4F 00 Twin peak filter OFF
01 Twin peak filter ON
50 00 Dial lock function OFF
01 Dial lock function ON
55 00 15 kHz roofing filter selection
01 6 kHz roofing filter selection
02 3 kHz roofing filter selection
56 00 SHARP selection for DSP filter type
01 SOFT selection for DSP filter type
57 00 WIDE selection for manual notch width
01 MID selection for manual notch width
02 NAR selection for manual notch width
58 00 WIDE selection for SSB transmit bandwidth
01 MID selection for SSB transmit bandwidth
02 NAR selection for SSB transmit bandwidth
17*
1
see p. 167 Send CW messages
18 00 Turn OFF the transceiver
01 Turn ON the transceiver*
2
19 00 Read the transceiver ID
1A 00 see p. 169 Send/read memory contents
01 see p. 166 Send/read band stacking register contents
02 see p. 166 Send/read memory keyer contents
03 00 to 49 Send/read the selected filter width
( SSB, CW, PSK: 00=50 Hz, 40=3600 Hz;
RTTY: 00=50 Hz, 31=2700 Hz;
AM: 00=200 Hz, 49=10 kHz)
04 00 to 13 Send/read the selected AGC time constant
( 00=OFF, 01=0.1/0.3 seconds,
13=6.0/8.0 seconds)
05
0001
see p. 168 Send/read SSB RX HPF/LPF
0002
00 to 10 Send/read SSB RX Tone (Bass) level
(00=–5, 10=+5)
0003
00 to 10 Send/read SSB RX Tone (Treble) level
(00=–5, 10=+5)
0004
see p. 168 Send/read AM RX HPF/LPF
Cmd.
Sub
cmd.
Data Description
1A 05 0005 00 to 10 Send/read AM RX tone (Bass) level
(00=–5, 10=+5)
0006 00 to 10 Send/read AM RX Tone (Treble) level
(00=–5, 10=+5)
0007 see p. 168 Send/read FM RX HPF/LPF
0008 00 to 10 Send/read FM RX tone (Bass) level
(00=–5, 10=+5)
0009 00 to 10 Send/read FM RX Tone (Treble) level
(00=–5, 10=+5)
0010 see p. 168 Send/read CW RX HPF/LPF
0011 see p. 168
Send/read RTTY RX
HPF/LPF
0012 see p. 168
Send/read PSK RX
HPF/LPF
0013 00 to 10 Send/read SSB TX Tone (Bass) level
(00=–5, 10=+5)
0014 00 to 10 Send/read SSB TX Tone (Treble) level
(00=–5, 10=+5)
0015 00 to 10 Send/read AM TX Tone (Bass) level
(00=–5, 10=+5)
0016 00 to 10 Send/read AM TX Tone (Treble) level
(00=–5, 10=+5)
0017 00 to 10 Send/read FM TX Tone (Bass) level
(00=–5, 10=+5)
0018 00 to 10 Send/read FM TX Tone (Treble) level
(00=–5, 10=+5)
0019 see p. 168 Send/read SSB TX bandwidth for WIDE
0020 see p. 168 Send/read SSB TX bandwidth for MID.
0021 see p. 168 Send/read SSB TX bandwidth for NARROW
0022 0000 to
0255
Send/read DRIVE gain
(0000=0%, 0255=100%)
0023 0000 to
0255
Send/read speech level
(0000=0%, 0255=100%)
0024 0000 to
0255
Send/read CW sidetone level
(0000=0%, 0255=100%)
0025 00 CW sidetone level limit OFF
01 CW sidetone level limit ON
0026 0000 to
0255
Send/read beep level
(0000=0%, 0255=100%)
0027 00 Beep level limit OFF
01 Beep level limit ON
0028 00 Squelch mute effect OFF (squelch is fixed
open) for audio output from USB-B connector
01 Squelch mute effect ON for audio output from
USB-B connector
0029 0000 to
0255
Send/read modulation level for audio input to
USB-B connector (0000=0%, 0255=100%)
0030 00 [MIC] selection for MOD input connector
during DATA OFF
01 [ACC] selection for MOD input connector
during DATA OFF
02 Both [MIC] and [ACC] selection for MOD
input connector during DATA OFF
03 [USB] selection for MOD input connector
during DATA OFF
0031 00 [MIC] selection for MOD input connector
during DATA1
01 [ACC] selection for MOD input connector
during DATA1
02 Both [MIC] and [ACC] selection for MOD
input connector during DATA1
03 [USB] selection for MOD input connector
during DATA1
0032 00 [MIC] selection for MOD input connector
during DATA2
01 [ACC] selection for MOD input connector
during DATA2
02 Both [MIC] and [ACC] selection for MOD
input connector during DATA2
03 [USB] selection for MOD input connector
during DATA2
Command table (continued) D
161
12
CONTROL COMMAND
*
1
While transmitting in the CW mode, or if the Break-in
function is ON, the transceiver transmits CW code when
the PC sends this command.
*
2
The power ON command (18 01) is available only when
the transceiver is remote standby mode. The transceiver
accepts the control command only from the [REMOTE] jack.
To Next Page
Loading...
