$6 MEMORY UP/DOWN SWITCHES [∫]/[√] (p. 107)
➥
Push to select the desired memory channel.
• Memory channels can be selected in both the VFO
and memory modes.
➥
Push to directly select the desired memory
channel after pushing [F-INP ENT] and a
memory channel number.
$7 MEMORY WRITE SWITCH [MW] (p. 109)
Stores the selected readout frequency and
operating mode into the displayed memory channel
when held down for 1 second.
• This function is available both in VFO and memory
modes.
$8 MEMO PAD-WRITE SWITCH [MP-W] (p. 112)
Programs the displayed readout frequency and
operating mode into a memo pad.
• The 5 most recent entries remain in memo pads.
• The memo pad capacity can be expanded from 5 to 10
in the Others set mode. (p. 140)
$9 MEMO PAD-READ SWITCH [MP-R] (p. 112)
Each push calls up a frequency and operating
mode in a memo pad. The 5 (or 10) most recently
programmed frequencies and operating modes can
be recalled, starting from the most recent.
• The memo pad capacity can be expanded from 5 to 10
in the Others set mode. (p. 140)
%0 VFO/MEMORY SWITCH [VFO/MEMO]
➥ Switches the selected readout operating mode
between the VFO and memory when pushed.
(pp. 28, 107)
➥ Transfers the memory contents to VFO when
held down for 1 second. (p. 110)
%1 QUICK TUNING SWITCH [TS]
➥ Turns the quick tuning step ON or OFF. (p. 32)
• While the quick tuning indicator, “Z,” is displayed
above the frequency display, the frequency can be
changed in programmed kHz steps.
• 0.1, 1, 5, 9, 10, 12.5, 20 and 25 kHz steps are
selectable for each operating mode independently.
➥ When the quick tuning step is ON, hold down
for 1 second to select the quick tuning step set
mode. (p. 32)
➥ When the quick tuning step is OFF, hold down
for 1 second to turn the 1 Hz tuning step ON or
OFF. (p. 32)
%2 AUDIO PEAK FILTER/TWIN PEAK FILTER
SWITCH [APF/TPF]
During CW mode operation (p. 43)
➥ Push to turn the audio peak filter ON or OFF.
• “ ” appears when audio peak filter is in use.
➥ When the audio peak filter is ON, hold down
for 1 second to select the APF passband width
between WIDE, MID and NAR or between 320,
160 and 80 Hz, depending on APF type setting
(SOFT or SHARP).
During RTTY mode operation (p. 51)
➥ Push to turn the twin peak filter ON or OFF.
• “ ” appears when twin peak filter is in use.
• The indicator on this switch lights green when the
function is activated.
■ Front panel (continued)
TWIN
-
PBT
RIT/ TX
Ӡ
NOTCH
CW PITCH
VOICE MEMORY
BAL NR
AF RF/SQL
MIC GAIN RF POWER BK
-
IN DELAYKEY SPEED
TIMER
PHONES
ELEC
-
KEY
MIC
AUTO
TUNE
GENEF
-
INP
1. 83.5
12
14
5
18
6
7
3
24
8
28
9
50
0
ENT
4
7
10
21
CHANGE
TS
XFC
SPLIT
DUAL
WATCH
MAIN
/
SUB
M.SCOPE
VFO/MEMO
MP
-
W
MW
MP
-
R
F
-
6
F
-
5
F
-
4
F
-
3
F
-
2
F
-
1
NRNB
PBT
-
CLR
APF/TPF
NOTCH
POWER
RIT
CLEAR
TX
Ӡ
SPEECH
LOCK
FILTER
RECPLAY
EXIT
/
SET
SSBCW
RTTY
/
PSK
AM/FM
MONITOR
TRANSMIT
TUNER
HF/50MHz TRANSCEIVER
LOCKTX RX SPLIT
$6
%2
$7 $8 $9 %0 %1
%3
%4
%5
9
1
PANEL DESCRIPTION
To Next Page
Loading...
