IDEC SmartRelay FL1D Series

To Next Page

To Previous Page

IDEC SmartRelay functions

173

IDEC SmartRelay Manual

View in parameter assignment mode:

B16

MI = 0100h

MN = 0017h

OT =00083h

Time interval

Time-to-go

Total operating hours

Courtesy of Steven Engineering, Inc. ● 230 Ryan Way, South San Francisco, CA 94080-6370 ● General Inquiries: (800) 670-4183 ● www.stevenengineering.com

Main Page

Default Chapter6
- Table of Contents6
1 Getting Started with IDEC Smartrelay11
2 IDEC Smartrelay Installation and Wiring23
- Modular IDEC Smartrelay Setup27
- Maximum Setup27
- Setup with Different Voltage Classes28
- Installing/Removing IDEC Smartrelay29
- DIN Rail Mounting30
- Wall-Mounting34
- Wiring IDEC Smartrelay36
- Connecting the Power Supply37
- Connecting IDEC Smartrelay Inputs39
- Connecting Outputs50
- Connecting the as Interface Bus54
- Putting into Operation56
- Switching on the IDEC Smartrelay/Power on56
- Operating States60
3 Programming IDEC Smartrelay62
- Connectors64
- Blocks and Block Numbers67
- The Way to IDEC Smartrelay, Starting with the Circuit Diagram70
- The Four Golden Rules for Operating IDEC Smartrelay73
- Overview of IDEC Smartrelay Menus75
- Writing and Starting the Circuit Program76
- Select Programming Mode76
- The First Circuit Program78
- Circuit Program Input79
- Assigning a Circuit Program Name85
- Password86
- Switching IDEC Smartrelay to RUN Mode91
- Second Circuit Program94
- Deleting a Block101
- Deleting Block Groups102
- Correcting Programming Errors103
- Selecting Analog Output Values for RUN/STOP Transition103
- Deleting the Circuit Program105
- Summertime/Wintertime Conversion106
- Synchronization111
- Memory Space and Circuit Dimensions112
4 IDEC Smartrelay Functions118
- Constants and Connectors - Co119
- Basic Functions List - GF122
- And124
- AND with Edge Detection125
- NAND (Not AND)126
- NAND with Edge Detection127
- NOR (Not OR)129
- XOR (Exclusive OR)130
- NOT (Negation, Inverter)130
- Basics on Special Functions131
- Designation of the Inputs132
- Time Response133
- Backup of the Real-Time Clock134
- Retentivity134
- Parameter Protection134
- Calculating the Gain and Offset of Analog Values135
- Special Functions List - SF138
- On-Delay142
- Off-Delay146
- On-/Off-Delay148
- Retentive On-Delay150
- Interval Time-Delay Relay / Pulse Output152
- Edge-Triggered Interval Time-Delay Relay154
- Asynchronous Pulse Generator157
- Random Generator159
- Stairwell Light Switch161
- Dual-Function Switch164
- Seven-Day Time Switch167
- Twelve-Month Time Switch172
- Up/Down Counter175
- Operating Hours Counter179
- Frequency Trigger184
- Analog Trigger187
- Analog Differential Trigger190
- Analog Comparator194
- Analog Value Monitoring199
- Analog Amplifier202
- Latching Relay205
- Current Impulse Relay206
- Message Texts209
- Softkey216
- Shift Register220
- Analog Multiplexer223
- Analog Ramp Control227
- PI Controller232
5 Configuring IDEC Smartrelay239
- Selecting Parameter Assignment Mode240
- Parameters242
- Selecting the Parameters243
- Modifying Parameters244
- Setting the Default Values for IDEC Smartrelay247
- Setting the Time-Of-Day and Date (FL1D-H12RC247
- Setting the Display Contrast249
- Setting the Start Screen250
6 IDEC Smartrelay Memory Cartridge (Card)251
- Security Function (Copyprotect)253
- Inserting and Removing the Memory Cartridge (Card)256
- Copying Data from the IDEC Smartrelay to the Memory Cartridge (Card)258
- Copying Data from the Memory Cartridge (Card) to IDEC Smartrelay260
7 IDEC Smartrelay Software262
- Connecting IDEC Smartrelay to a PC265
8 Applications267
- Stairway or Corridor Lighting269
- Requirements for a Stairway Lighting System269
- Previous Solution269
- Lighting System with IDEC Smartrelay270
- Special Features and Expansion Options272
- Automatic Door273
- Requirements of an Automatic Door273
- Conventional Solution274
- Door Control System with IDEC Smartrelay274
- Special Features and Expansion Options277
- Extended Solution with FL1D-H12RCC277
- Air-Conditioning System280
- Requirements for an Air-Conditioning System280
- Advantages of Using IDEC Smartrelay283
- Factory Door285
- Requirements for a Gate Control System285
- Previous Solution286
- Extended IDEC Smartrelay Solution288
- Centralized Control and Monitoring of Several Factory Doors289
- Requirements for a Gate Control System290
- Luminous Rows293
- Requirements for a Lighting System293
- Previous Solution294
- Luminous Row Control System with FL1D-H12RCC295
- Service Water Pump297
- Requirements for a Control System of a Service Water Pump298
- Previous Solution298
- Service Water Pump System with FL1D-H12RCC299
- Special Features and Expansions300
- Benefits of IDEC Smartrelay301
A Technical Data303
General Technical Data303
Technical Data: FL1D-H12RCC/FL1D-B12RCC and FL1B-M08C2R2305
Technical Data: FL1D-H12SND and FL1B-M08B1S2308
Technical Data: FL1D-H12RCA/FL1D-B12RCA and FL1B-M08D2R2311
Technical Data: FL1D-H12RCE/FL1D-B12RCE and FL1B-M08B2R2314
Switching Capacity and Service Life of the Relay Outputs308318
Technical Data: FL1B-J2B2319
Technical Data: FL1D-K2B2320
B Determining the Cycle Time321
CIDEC Smartrelay Without Display323
DIDEC Smartrelay Menu Structure326
E Type Numbers328
Index330

IDEC SmartRelay FL1D Series - Page 183

Table of Contents

Related product manuals