Name: IDEC SmartRelay FL1D Series
Brand: IDEC
Rating: 4 (1 reviews)

To Next Page

To Previous Page

Applications

IDEC SmartRelay Manual 274

You can also generate a message at output Q4:

Error Messege

The relay contacts of output Q4 are always closed when the

system is in operation. Relay Q4 does not drop off unless

there is a power failure or a fault in the system. This contact

can be used for remote monitoring, for example.

Courtesy of Steven Engineering, Inc. ● 230 Ryan Way, South San Francisco, CA 94080-6370 ● General Inquiries: (800) 670-4183 ● www.stevenengineering.com

Default Chapter6
- Table of Contents6
1 Getting Started with IDEC Smartrelay11
2 IDEC Smartrelay Installation and Wiring23
- Modular IDEC Smartrelay Setup27
- Maximum Setup27
- Setup with Different Voltage Classes28
- Installing/Removing IDEC Smartrelay29
- DIN Rail Mounting30
- Wall-Mounting34
- Wiring IDEC Smartrelay36
- Connecting the Power Supply37
- Connecting IDEC Smartrelay Inputs39
- Connecting Outputs50
- Connecting the as Interface Bus54
- Putting into Operation56
- Switching on the IDEC Smartrelay/Power on56
- Operating States60
3 Programming IDEC Smartrelay62
- Connectors64
- Blocks and Block Numbers67
- The Way to IDEC Smartrelay, Starting with the Circuit Diagram70
- The Four Golden Rules for Operating IDEC Smartrelay73
- Overview of IDEC Smartrelay Menus75
- Writing and Starting the Circuit Program76
- Select Programming Mode76
- The First Circuit Program78
- Circuit Program Input79
- Assigning a Circuit Program Name85
- Password86
- Switching IDEC Smartrelay to RUN Mode91
- Second Circuit Program94
- Deleting a Block101
- Deleting Block Groups102
- Correcting Programming Errors103
- Selecting Analog Output Values for RUN/STOP Transition103
- Deleting the Circuit Program105
- Summertime/Wintertime Conversion106
- Synchronization111
- Memory Space and Circuit Dimensions112
4 IDEC Smartrelay Functions118
- Constants and Connectors - Co119
- Basic Functions List - GF122
- And124
- AND with Edge Detection125
- NAND (Not AND)126
- NAND with Edge Detection127
- NOR (Not OR)129
- XOR (Exclusive OR)130
- NOT (Negation, Inverter)130
- Basics on Special Functions131
- Designation of the Inputs132
- Time Response133
- Backup of the Real-Time Clock134
- Retentivity134
- Parameter Protection134
- Calculating the Gain and Offset of Analog Values135
- Special Functions List - SF138
- On-Delay142
- Off-Delay146
- On-/Off-Delay148
- Retentive On-Delay150
- Interval Time-Delay Relay / Pulse Output152
- Edge-Triggered Interval Time-Delay Relay154
- Asynchronous Pulse Generator157
- Random Generator159
- Stairwell Light Switch161
- Dual-Function Switch164
- Seven-Day Time Switch167
- Twelve-Month Time Switch172
- Up/Down Counter175
- Operating Hours Counter179
- Frequency Trigger184
- Analog Trigger187
- Analog Differential Trigger190
- Analog Comparator194
- Analog Value Monitoring199
- Analog Amplifier202
- Latching Relay205
- Current Impulse Relay206
- Message Texts209
- Softkey216
- Shift Register220
- Analog Multiplexer223
- Analog Ramp Control227
- PI Controller232
5 Configuring IDEC Smartrelay239
- Selecting Parameter Assignment Mode240
- Parameters242
- Selecting the Parameters243
- Modifying Parameters244
- Setting the Default Values for IDEC Smartrelay247
- Setting the Time-Of-Day and Date (FL1D-H12RC247
- Setting the Display Contrast249
- Setting the Start Screen250
6 IDEC Smartrelay Memory Cartridge (Card)251
- Security Function (Copyprotect)253
- Inserting and Removing the Memory Cartridge (Card)256
- Copying Data from the IDEC Smartrelay to the Memory Cartridge (Card)258
- Copying Data from the Memory Cartridge (Card) to IDEC Smartrelay260
7 IDEC Smartrelay Software262
- Connecting IDEC Smartrelay to a PC265
8 Applications267
- Stairway or Corridor Lighting269
- Requirements for a Stairway Lighting System269
- Previous Solution269
- Lighting System with IDEC Smartrelay270
- Special Features and Expansion Options272
- Automatic Door273
- Requirements of an Automatic Door273
- Conventional Solution274
- Door Control System with IDEC Smartrelay274
- Special Features and Expansion Options277
- Extended Solution with FL1D-H12RCC277
- Air-Conditioning System280
- Requirements for an Air-Conditioning System280
- Advantages of Using IDEC Smartrelay283
- Factory Door285
- Requirements for a Gate Control System285
- Previous Solution286
- Extended IDEC Smartrelay Solution288
- Centralized Control and Monitoring of Several Factory Doors289
- Requirements for a Gate Control System290
- Luminous Rows293
- Requirements for a Lighting System293
- Previous Solution294
- Luminous Row Control System with FL1D-H12RCC295
- Service Water Pump297
- Requirements for a Control System of a Service Water Pump298
- Previous Solution298
- Service Water Pump System with FL1D-H12RCC299
- Special Features and Expansions300
- Benefits of IDEC Smartrelay301
A Technical Data303
General Technical Data303
Technical Data: FL1D-H12RCC/FL1D-B12RCC and FL1B-M08C2R2305
Technical Data: FL1D-H12SND and FL1B-M08B1S2308
Technical Data: FL1D-H12RCA/FL1D-B12RCA and FL1B-M08D2R2311
Technical Data: FL1D-H12RCE/FL1D-B12RCE and FL1B-M08B2R2314
Switching Capacity and Service Life of the Relay Outputs308318
Technical Data: FL1B-J2B2319
Technical Data: FL1D-K2B2320
B Determining the Cycle Time321
CIDEC Smartrelay Without Display323
DIDEC Smartrelay Menu Structure326
E Type Numbers328
Index330

Questions and Answers:

Need help?

Do you have a question about the IDEC SmartRelay FL1D Series and is the answer not in the manual?

IDEC SmartRelay FL1D Series Specifications

General

Brand	IDEC
Model	SmartRelay FL1D Series
Category	Control Unit
Language	English

Related product manuals

IDEC MicroSmart Series

17 pages

IDEC FC6A-C16K1CE

252 pages

IDEC SmartRelay FL1D Series User Manual

Table of Contents

Questions and Answers:

IDEC SmartRelay FL1D Series Specifications

Related product manuals