Ingenico 5100 - TCP-IP with Dial Back-up Configuration

SKYZER TECHNOLOGIES PAGE 28 OF 97
INGENICO 5100 PAYMARK VERSION 6.0 OPERATING GUIDE Version 1.3
3.2.2 TCP-IP with Dial Back-up Configuration
1.0
PRIMARY
PRIMARYPRIMARY
PRIMARY
HOST IP ADDRESS
HOST IP ADDRESSHOST IP ADDRESS
HOST IP ADDRESS
117.120.3
117.120.3117.120.3
117.120.34.110
4.1104.110
4.110
This parameter specifies the Primary Host IP Address. By default it is set to
117.120.34.110.
Press ENTER.
2.0
PRIMARY
PRIMARYPRIMARY
PRIMARY
HOST PORT
HOST PORTHOST PORT
HOST PORT
33876
3387633876
33876
This parameter specifies the Primary TCP/IP Port Number of Paymark IP Host.
3.0
SECONDARY
SECONDARYSECONDARY
SECONDARY
HOST IP ADDRESS
HOST IP ADDRESSHOST IP ADDRESS
HOST IP ADDRESS
117.120.3
117.120.3117.120.3
117.120.32
22
2.
..
.110
110110
110
This parameter specifies the Secondary Host IP Address. By default, it is set to
117.120.32.110.
Press ENTER.
4.0
SECONDARY
SECONDARYSECONDARY
SECONDARY
HOST PORT
HOST PORTHOST PORT
HOST PORT
33876
3387633876
33876
This parameter specifies the Secondary TCP/IP Port Number of Paymark IP Host.
5.0
ENABLE DHCP Y/N
ENABLE DHCP Y/NENABLE DHCP Y/N
ENABLE DHCP Y/N
1
11
1-
--
-YES 2
YES 2YES 2
YES 2-
--
-NO
NONO
NO
Press the corresponding number key and press ENTER to set the IP address for the
terminal.
Option 1 – to allow the terminal to dynamically obtain its IP address and proceed
with step 7.0. Option 1 is the default value.
NOTE: When terminal is configured for DHCP, reboot the terminal by
pressing and releasing the shortcut keys (CHQ + SAV + CANCEL) at the
same time. This will enable the terminal to obtain the IP addresses from
the router.
Option 2 – to enter in static IP address for the terminal and proceed with step 4.0
NOTE: When configuring the terminal for Static IP address, ensure to
obtain the IP address, subnet mask and default gateway IP address from
your ISP (Internet Service Provider) for connectivity to Paymark network.
6.0
TERM IP ADDRESS
TERM IP ADDRESSTERM IP ADDRESS
TERM IP ADDRESS
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXXXXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
Enter in the static IP address for the terminal.
Example: 192.10.1.14
Note: Press the FUNC key to insert a dot in between numbers.
7.0
SUBNET MASK
SUBNET MASKSUBNET MASK
SUBNET MASK
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXXXXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
Enter in the subnet mask for the static IP address.
Example: 255.255.255.0
8.0
GATEWAY IP ADDR
GATEWAY IP ADDRGATEWAY IP ADDR
GATEWAY IP ADDR
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXXXXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
Enter in the gateway IP address to forward the packets from.
Example: 192.10.1.1
9.0
QUICK DIAL?
QUICK DIAL?QUICK DIAL?
QUICK DIAL?
1
11
1-
--
-YES 2
YES 2YES 2
YES 2-
--
-NO
NONO
NO
This parameter sets up the way that the terminal dials. Select the mode by pressing
the corresponding number key.