Kyocera FS-2020D Service Manual

2J0/2J1/2J2-4
2-2-4
13. Power source unit ........................................ Generates 24 V DC and 5 V DC power source. Controls the fuser heater
lamp.
14. Power switch................................................ Turns ON/OFF the AC power source.
15. Interlock switch ............................................ Shuts off 24 V DC power line when the top cover is opened.
16. Cassette size switch .................................... Detects the paper size dial setting of the paper setting dial.
17. Fuser unit switch .......................................... Detects open/close rear unit (fuser unit).
18. Envelope switch-R ....................................... Detects the position of the envelope switch (right).
19. Envelope switch-L........................................ Detects the position of the envelope switch (left).
20. Envelope feeder detection switch*
2
............. Detects optional envelope feeder.
21. Registration sensor ...................................... Detects the timing of primary feeding.
22. Paper gauge sensor 1.................................. Detects the paper remaining amount level.
23. Paper gauge sensor 2.................................. Detects the paper remaining amount level.
24. Duplex jam sensor ....................................... Detects paper jam in the duplex conveying section.
25. MP tray paper feed sensor........................... Detects paper on the MP tray.
26. Face down tray paper full sensor................. Detects whether the face down tray is full.
27. Paper exit sensor ......................................... Detects paper jam in the fuser unit.
28. Duplex sensor*
2
........................................... Detects paper jam in the rear unit.
29. Temperature/humidity sensor....................... Detects the ambient temperature and absolute humidity.
30. Lift sensor*
2
................................................. Detects activation of upper limit of the bottom plate in the paper cassette.
31. Toner sensor ................................................ Detects the toner in the toner container.
32. Fuser thermistor 1........................................ Measures the heat roller temperature.
33. Fuser thermistor 2*
2
..................................... Measures the heat roller (center) temperature.
34. Thermal cutout ............................................. Shuts off the power source to the fuser heater lamp when the heat roller
reaches extremely high temperature.
35. Main motor ................................................... Drives the paper feed/conveying section and fuser unit.
36. Drum motor .................................................. Drives the drum unit and developing unit.
37. Toner motor.................................................. Replenishes the developing unit with toner.
38. Switchback motor......................................... Drives paper exit (switchback) section.
39. Lift motor*
2
................................................... Operates the bottom plate in the paper cassette.
40. Polygon motor.............................................. Drives the polygon mirror.
41. Right fan motor ............................................ Cools the interior of machine.
42. Left fan motor............................................... Cools the interior of machine.
43. PSU fan motor ............................................. Cools the power source unit.
44. Feed fan motor............................................. Cools the paper feed conveying section and duplex conveying section.
45. Exit fan motor............................................... Disperses steam.
46. Registration clutch ....................................... Controls the secondary paper feed.
47. Paper feed clutch ......................................... Controls the paper cassette paper feed.
48. Middle feed clutch ........................................ Controls the paper conveying at the conveying section.
49. Duplex clutch*
2
............................................ Controls the paper conveying at the duplex conveying section.
50. Developer solenoid ...................................... Controls the developing unit drive.
51. MP tray paper feed solenoid ........................ Controls the primary paper feed from the MP tray.
52. Face up/down solenoid*
2
............................. Switches the output stack between face up and face down.
53. Fuser heater lamp........................................ Heats the heat roller.
54. AC inlet ........................................................ Connects the AC power source.
*
1
: 45/47 ppm printer (EUR/USA model) only
*
2
: 40/42 and 45/47 ppm printers (EUR/USA model) only

Kyocera FS-2020D Specifications

General

Color	No
Duplex printing	Yes
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	9 s
Print speed (black, normal quality, A4/US Letter)	35 ppm
Memory type	DDR2
Processor model	PowerPC 440
Maximum internal memory	1152 MB
Sound power level (standby)	29 dB
Sound pressure level (printing)	52 dB
Power supply type	220/240 V, 50/60 Hz
Capacity cartridge	12000 sheets
Power consumption (active)	560 W
Recommended monthly print volume	20000 pages
Maximum duty cycle	150.000 pages per month
Number of print cartridges	1
Total input capacity	500 sheets
Total output capacity	250 sheets
Maximum input capacity	1100 sheets
Maximum number of input trays	2
Multi-Purpose tray input capacity	100 sheets
Maximum print size	216 x 356 mm
Paper tray media types	Plain paper, Recycled paper
Paper tray media weight	60 - 120 g/m²
Non-ISO print media sizes	Letter
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5
Maximum ISO A-series paper size	A4
Multi-Purpose Tray media weight	60 - 220 g/m²
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	9.2 W
Power consumption (PowerSave)	5.7 W
Energy Star Typical Electricity Consumption (TEC)	2.6 kWh/week
Display	LCD
Certification	GS, TüV, CE
Standard interfaces	Parallel, USB 2.0
Optional connectivity	Ethernet, Wireless LAN
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Dimensions (WxDxH)	382 x 394 x 285 mm