Kyocera FS-2020D operation panel is off, what to do?
If nothing lights up on the operation panel of your Kyocera Printer, and the fan isn't running when you turn it on, ensure the power cord is properly plugged into the power outlet at both ends. Try replacing the power cord. Also, check that the power switch is in the On ( | ) position.
How to resolve gray background issue on my Kyocera Printer?
If your Kyocera printer displays 'Gray background' and the [Attention] indicator is flashing, it means the toner is low. Install a new toner kit. Also, adjust the print density by accessing the print menu from the operation panel and selecting a lighter density setting.
How to remove dirt on paper from Kyocera Printer?
To correct this, clean the parts in the paper paths, such as the paper cassette, etc.
Why is my Kyocera FS-2020D emitting vapor from the rear?
If your Kyocera printer is emitting vapor from the rear, it may be due to low temperature near the printer or humidity in the paper. Heat generated during printing can evaporate moisture, causing the vapor. This is not a problem and printing can continue. To reduce the vapor, increase the room temperature and use paper stored in a dry place.
Why does my Kyocera FS-2020D Printer say 'Enter Account'?
If your Kyocera printer displays 'Enter Account', it indicates that an account code must be entered. This message appears if you attempt to print from the operation panel (e.g., printing a status page or using the Job Retention function) when the Job Accounting function is enabled.
What does 'Call service F###:' mean on my Kyocera FS-2020D Printer?
Call for service. The printer does not operate when this message is displayed.
How to fix gray background on Kyocera FS-2020D Printer?
If your Kyocera Printer is showing a gray background on prints, check the operation panel for the Toner low message and a flashing [Attention] indicator; if present, install a new toner kit. You can also adjust the print density by accessing the print menu on the operation panel and selecting a lighter setting.
Why is my Kyocera Printer printing completely blank pages?
If you are getting completely blank printouts from your Kyocera printer, check the toner container. Open the top cover and make sure the toner container is correctly installed in the printer. Also, verify that the application software is operating correctly.
Why won't my Kyocera FS-2020D turn on?
If nothing lights up on the operation panel of your Kyocera printer, and the fan makes no noise, make sure the power cord is properly plugged into the power outlet. Connect both ends of the power cord securely and try replacing the power cord. Also, check that the power switch is in the On (|) position.
How to fix black or white vertical streaks on Kyocera FS-2020D Printer?
If your Kyocera Printer is producing black or white vertical streaks, check the operation panel for a Toner low message. If displayed, install a new toner kit.
General| Color | No |
|---|---|
| Duplex printing | Yes |
| Print technology | Laser |
| Maximum resolution | 1200 x 1200 DPI |
| Time to first page (black, normal) | 9 s |
| Print speed (black, normal quality, A4/US Letter) | 35 ppm |
| Memory type | DDR2 |
| Processor model | PowerPC 440 |
| Maximum internal memory | 1152 MB |
| Sound power level (standby) | 29 dB |
| Sound pressure level (printing) | 52 dB |
| Power supply type | 220/240 V, 50/60 Hz |
| Capacity cartridge | 12000 sheets |
| Power consumption (active) | 560 W |
| Recommended monthly print volume | 20000 pages |
| Maximum duty cycle | 150.000 pages per month |
| Number of print cartridges | 1 |
| Total input capacity | 500 sheets |
| Total output capacity | 250 sheets |
| Maximum input capacity | 1100 sheets |
| Maximum number of input trays | 2 |
| Multi-Purpose tray input capacity | 100 sheets |
| Maximum print size | 216 x 356 mm |
| Paper tray media types | Plain paper, Recycled paper |
| Paper tray media weight | 60 - 120 g/m² |
| Non-ISO print media sizes | Letter |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5 |
| Maximum ISO A-series paper size | A4 |
| Multi-Purpose Tray media weight | 60 - 220 g/m² |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 9.2 W |
| Power consumption (PowerSave) | 5.7 W |
| Energy Star Typical Electricity Consumption (TEC) | 2.6 kWh/week |
| Display | LCD |
| Certification | GS, TüV, CE |
| Standard interfaces | Parallel, USB 2.0 |
| Optional connectivity | Ethernet, Wireless LAN |
| Sustainability certificates | ENERGY STAR |
Weight and Dimensions| Dimensions (WxDxH) | 382 x 394 x 285 mm |
|---|
Explains hazard levels (DANGER, WARNING, CAUTION) and safety symbols used.
Detailed technical specifications for printer models.
Identification and listing of printer components.
Diagrams showing internal printer structure and component layout.
Requirements for optimal printer setup location and conditions.
Procedure for safely removing the printer from its packaging.
Steps to install optional memory modules.
Steps to install optional memory cards.
Accessing and using the printer's service and diagnostic functions.
Detailed explanation of available maintenance functions.
Diagnosing and resolving paper jam issues.
Understanding and using printer error codes for diagnosis.
Identifying and correcting print quality issues.
Troubleshooting electrical faults and error messages.
Safety guidelines for handling printer parts during maintenance.
Procedures for removing and replacing external printer covers.
Disassembly and reassembly of paper feeding mechanisms.
Steps for removing and installing the developing unit.
Procedures for detaching and refitting the drum unit.
Procedures for removing and replacing the fuser unit and its parts.
Instructions for removing and installing Printed Circuit Boards (PWBs).
Process for updating printer firmware via USB or memory card.
Specific steps for firmware update using a USB drive.
Mechanical details of the paper feeding system.
Mechanical details of the drum unit and its components.
Mechanical details of the laser scanner unit.
Mechanical details of the developing unit and toner system.
Mechanical details of the fuser unit and its heating system.
Mechanical details of paper exit and rear unit components.
Diagrams showing the location of electrical components.
Block diagram and function of the power source PWB.
Block diagram and function of the engine PWB.
Chart showing distances for common recurring print defects.
Electrical wiring schematics for the 35 ppm model.
Electrical wiring schematics for the 40 ppm model.
Electrical wiring schematics for the 45 ppm model.
To Next Page
