Maxcess FIFE DP-20 PLUS User Manual

DP-20 PLUS Web Guide Controller 3-2
4th Quarter 2021 © 2021 Maxcess International. All rights reserved. Figure Sheet 2-320 A
Setup Menu Chart
AUTOMATIC MODE
1X.1
1X.2
1X.3
1X.4
1X.5
Gain
Guide Point
Measurement
About
Exit Menus
SERVO-CENTER MODE
2X.1
2X.2
2X.3
2X.4
2X.5
Servo-Center
Gain
Servo-Center
Guide Point
Measurement
About
Exit Menus
MANUAL MODE
SELECT MENU
3X.1
3X.2
3X.3
3X.4
3X.5
3X.6
3X.7
BASIC
SPECIAL
ADVANCED
LANGUAGE
CUSTOM
ABOUT
Exit Menus
BASIC MENUS
3X.1.1
3X.1.2
3X.1.3
3X.1.4
3X.1.5
3X.1.6
3X.1.7
3X.1.8
3X.1.9
Gain
Guide Point
Guide
Polarity
Calibration
Auto Setup
Servo-Center
Gain
Servo-Center
Polarity
Measurem
ent
Exit
Menus
SPECIAL MENUS
3X.2.1
3X.2.2
3X.2.3
3X.2.4
3X.2.5
3X.2.6
3X.2.7
3X.2.8
3X.2.9
Deadband
Set Operation
Mode Enable
Set Sensor
Mode Enable
Set Jog
Enable
Set Jog
Polarity
Set
Jog Speed
Set
Sensor Type
Sensor
Voltage
Exit
Menus
ADVANCED MENUS
3X.3.1
3X.3.2
3X.3.3
3X.3.4
3X.3.5
3X.3.6
3X.3.7
3X.3.8
3X.3.9
Restore
Settings
Backup
Settings
Set
Password
Set Output
Delay
Output A
Set Output
Delay
Output B
Set Loss of
Null
Output
Digital I/O (X3)
Enable/Disable
Test
Signals
Exit
Menus
LANGUAGE MENU
3X.4.1
Select
Language
CUSTOM MENUS
3X.5.1
3X.5.2
3X.5.3
3X.5.4
3X.5.5
3X.5.6
3X.5.7
3X.5.8
LCD Contrast
ASC Control
Set ASC
Limits
Set ASC
Source
Output
Polarity
Set RGPC
Speed
X3 Link
Exit
Menus
ABOUT MENUS
1X.4.1
2X.4.1
3X.6.1
1X.4.2
2X.4.2
3X.6.2
1X.4.3
2X.4.3
3X.6.3
1X.4.4
2X.4.4
3X.6.4
1X.4.5
2X.4.5
3X.6.5
Serial Number
FW Number
SW Number
SM Number
Exit Menus
MEASUREMENT SUBMENUS
1X.3.1
2X.3.1
3X.1.8.1
1X.3.2
2X.3.2
3X.1.8.2
1X.3.3
2X.3.3
3X.1.8.3
1X.3.4
2X.3.4
3X.1.8.4
1X.3.5
2X.3.5
3X.1.8.5
1X.3.6
2X.3.6
3X.1.8.6
1X.3.7
2X.3.7
3X.1.8.7
1X.3.8
2X.3.8
3X.1.8.8
Sensor Signal
Edge L (X4) or
Line C (X4)
Sensor Signal
Edge R (X5) or
Line E (X4)
Sensor Signal
Servo-Center
(X2)
Motor
Type
Tachometer
Signal
Motor
Current
Digital
I/O
Exit
Menus
TEST SIGNALS SUBMENUS
3X.3.8.1
3X.3.8.2
3X.3.8.3
3X.3.8.4
Sensor
Current
Toggle
Outputs
Guide Test
Mode
Exit
Menus
Notes:
1. The ‘X’ in the Menu Number may be A, B, C, D, or E, depending on the sensor mode.
2. The highlighted menus can be set for password protection. If a password has been set, the menu line 1 will have an X as the initial character.

Maxcess FIFE DP-20 PLUS Specifications

General

Brand	Maxcess
Model	FIFE DP-20 PLUS
Category	Controller
Language	English