To Next PageTo Next Page
Need help?Do you have a question about the MBRAUN LABmaster 130 and is the answer not in the manual?
Details about system designation, series number, and responsible persons.
Provides M.Braun's contact details, address, phone, fax, and website.
Guidelines for reading the manual and following safety regulations.
Manufacturer's disclaimer regarding improper use, modifications, and data loss.
Conditions under which the equipment warranty expires.
Safe handling of substances, inert gas use, and ventilation requirements.
Potential dangers from mechanical, electrical, chemical, and other hazards.
Hazards related to moving parts and material ejection, use of genuine parts.
Risks associated with high voltages, proper grounding, and fuse replacement.
Precautions against electrostatic discharge when handling electronic parts.
Guidelines for handling chemicals, corrosives, solvents, and gases safely.
Explains various caution and command symbols found on the system.
Procedures to follow in case of an emergency, including shutdown and contact.
Conditions under which the system is considered unsafe for operation.
Overview of M.Braun glovebox systems and their functions.
Explanation of the PLC-operated pressure control system and its parameters.
Methods and guidelines for replacing ambient air with working gas.
Normal operation mode where gas is circulated and purified.
Process to restore purifier filter effectiveness by removing accumulated elements.
Detailed steps for transferring materials using the antechamber in auto or manual modes.
Information on oxygen and moisture analyzers, their function, and maintenance.
How to interact with the system via the touch screen display.
How to enter data and use password-protected fields on the touch screen.
Steps to navigate to and view system information screens.
Introduction to the system's touch screen interface and button functions.
Description of the main screen and access to other functions.
Overview of accessed screens via the Common Parameters button.
How to set alarm parameters for analyzers and cooling units.
Displays highest and lowest detected levels and how to reset them.
Details on activating and deactivating system functions via buttons.
Operating the large antechamber, including status fields and controls.
Setting parameters for automatic antechamber cycles.
Setting upper and lower limits for box pressure.
Setting and viewing temperatures for freezer and cooling units.
Lists and describes warning messages and error codes.
Recommended room conditions, temperature, and clearance for glovebox placement.
Specifications for working and regeneration gases, types, purity, and pressure.
Recommendations for venting the glovebox system and vacuum pump.
Information on power supply and required outlet types.
Specifications for connecting the heat exchanger for box atmosphere cooling.
Overview of the glovebox assembly process and information binder contents.
Lists tools and materials needed for installation, not supplied by M.Braun.
Instructions for assembling stand-mounted and stand-alone purifier glovebox systems.
Steps for attaching gauges and sensors to the antechamber.
Installing electrical feedthroughs and the power strip inside the glovebox.
Connecting the vacuum pump and other components for stand-mounted purifiers.
Connecting components for stand-alone purifier systems.
Instructions for installing the oil mist filter on the vacuum pump.
Steps for properly attaching gloves to the gloveports.
Connecting cables for freezers and compressors.
Steps for connecting oxygen and moisture analyzers.
Adjusting the system's leveling feet for stability.
Connecting the main power and gas supplies to complete installation.
Overview of system activation, pressure testing, and purging.
Steps to power on the system and access initial screens.
Performing leak tests in positive and negative pressure states.
Procedures for purging the glovebox atmosphere with working gas.
Using the glovebox for normal operation in circulation mode.
Starting and adjusting circulation mode, handling high oxygen levels.
Activating and deactivating oxygen and moisture analyzers.
Step-by-step guide for material transfer using the large antechamber.
Manual operation procedures for the mini antechamber.
How to activate and set parameters for the freezer unit.
Process for regenerating the purifier to maintain effectiveness.
Overview of maintenance and troubleshooting for the glovebox system.
Daily, quarterly, and annual maintenance tasks for components.
Procedures for calibrating, cleaning, and setting date/time on the touch panel.
Step-by-step guide for safely replacing worn or damaged gloves.
Instructions for cleaning and maintaining the moisture analyzer probe.
Troubleshooting guidelines for common alarm conditions.
General| Type | Glovebox |
|---|---|
| Inert Gas | Nitrogen or Argon |
| Oxygen Level | < 1 ppm |
| Humidity Level | < 1 ppm |
| Leak rate | < 0.05 Vol%/h |
| Water Level | < 1 ppm |
| Glove Ports | 2 |
| Feedthroughs | Electrical, gas |
| Material | Stainless steel |
| Pressure Range | +/- 15 mbar |
| Regeneration | Automatic |
