Motorola Symbol LS3408 Product Reference Guide

354 pages

To Next Page

Symbol LS3408

Product Reference Guide

Default Chapter5
- Revision History5
- Table of Contents7
About this Guide15
- Introduction15
- Chapter Descriptions15
- AIM Code Identifiers16
- Service Information17
Chapter 1 Getting Started19
- Introduction19
- Unpacking the Scanner20
- Setting up the Scanner21
Chapter 2 Scanning25
- Introduction25
- Beeper Definitions26
- LED Definitions27
- Scanning in Hand-Held Mode27
  - Aiming28
- Scanning in Hands-Free Mode29
- Decode Zone30
Chapter 3 Maintenance and Technical Specifications33
- Introduction33
- Maintenance33
- Troubleshooting34
- Technical Specifications36
- Scanner Signal Descriptions38
Chapter 4 User Preferences41
- Introduction41
- Scanning Sequence Examples41
- Errors While Scanning42
- User Preferences Default Parameters42
- User Preferences43
Chapter 5 Keyboard Wedge Interface49
- Introduction49
- Connecting a Keyboard Wedge Interface50
- Keyboard Wedge Default Parameters51
- Keyboard Wedge Host Types52
- ASCII Character Set61
Chapter 6 RS-232 Interface71
- Introduction71
- Connecting an RS-232 Interface72
- RS-232 Default Parameters73
- Host Parameters74
- ASCII / Character Set89
Chapter 7 USB Interface95
- Introduction95
- Connecting a USB Interface96
- USB Default Parameters97
- USB Host Parameters98
- ASCII Character Set106
Chapter 8 IBM 468X/469X Interface117
- Introduction117
- Connecting to an IBM 468X/469X Host118
- IBM Default Parameters119
- IBM 468X/469X Host Parameters120
  - Port Address120
  - Convert Unknown to Code 39120
Chapter 9 Wand Emulation Interface123
- Introduction123
- Connecting a Wand Emulation Interface124
- Wand Emulation Default Parameters125
- Wand Emulation Host Parameters126
Chapter 10 Scanner Emulation Interface131
- Introduction131
- Connecting Using Scanner Emulation132
- Scanner Emulation Default Parameters133
- Scanner Emulation Host134
- Scanner Emulation Host Parameters134
Chapter 11 123Scan143
- Introduction143
- Communication with 123Scan143
- 123Scan Parameter144
Chapter 12 Symbologies145
- Introduction145
- Scanning Sequence Examples145
- Errors While Scanning145
- Symbology Default Parameters146
- Upc/Ean149
- Code 128162
- Code 93169
  - Enable/Disable Code 93169
  - Set Lengths for Code 93169
- Code 11171
- Interleaved 2 of 5 (I 2 of 5)175
- Discrete 2 of 5 (D 2 of 5)179
  - Enable/Disable Discrete 2 of 5179
  - Set Lengths for Discrete 2 of 5179
- Codabar (NW - 7)181
- Msi184
- GS1 Databar (Formerly Reduced Space Symbology)188
- Redundancy Level 1190
- Security Level 0192
- Bi-Directional Redundancy193
Chapter 13 Miscellaneous Scanner Options195
- Introduction195
- Scanning Sequence Examples195
- Errors While Scanning195
- Miscellaneous Default Parameters196
- Miscellaneous Scanner Parameters197
Chapter 14 Advanced Data Formatting203
- Introduction203
- Rules: Criteria Linked to Actions203
- Using ADF Bar Codes204
- ADF Bar Code Menu Example204
- Special Commands208
- Criteria211
- Actions225
- Alphanumeric Keyboard301
Appendix A Standard Default Parameters319
Appendix B: Programming Reference322
Appendix C: Sample Bar Codes322
- Upc-E1322
- Code 39322
- Trioptic Code 39322
- Code 93322
- Code 11322
- Interleaved 2323
Appendix D Numeric Bar Codes335
- Cancel337
Glossary339

Other manuals for Motorola Symbol LS3408

Quick Start Guide2 pages

Questions and Answers:

L
Lisa JohnsonAug 18, 2025
What to do if the Motorola Symbol LS3408 Scanner laser comes on, but doesn't decode the bar code?
- B
  Bryan RiosAug 18, 2025
  If the Motorola Scanner's laser is on but it doesn't decode the bar code, consider these potential causes and solutions: * Ensure the scanner is programmed to read the type of bar code being scanned. * Check the bar code symbol to ensure it is not defaced. Try scanning test bar codes of the same bar code type. * Adjust the scanner's distance: move it closer to or further from the bar code.