Motorola TC55 Integrator Guide

• MSI
- Length 1 - Use to set decode lengths (default - 4). See Decode Lengths on page 58 for more information.
- Length 2 - Use to set decode lengths (default - 55). See Decode Lengths on page 58 for more information.
- Redundancy - Sets the reader to read the bar code twice before accepting data. A check in the checkbox
indicates that redundancy is enabled (default - enabled).
- Check Digit - With MSI symbols, one check digit is mandatory and always verified by the reader. The second
check digit is optional.
+ One Check Digit - Verify one check digit (default).
+ Two Check Digits - Verify two check digits.
- Check Digit Scheme - Two algorithms are possible for the verification of the second MSI check digit. Select
the algorithm used to encode the check digit.
+ Mod-11-10 - First check digit is MOD 11 and second check digit is MOD 10 (default).
+ Mod-10-10 - Both check digits are MOD 10.
- Report Check Digit - Transmit MSI data with or without the check digit. A check in the checkbox indicates to
send MSI data with check digit (default - disabled).
• Code93
- Length1 - Use to set decode lengths (default - 0). See Decode Lengths on page 58 for more information.
- Length2 - Use to set decode lengths (default - 55). See Decode Lengths on page 58 for more information.
- Redundancy - Sets the reader to read the bar code twice before accepting data. A check in the checkbox
indicates that redundancy is enabled (default - disabled).
• Discrete 2 of 5
- Length1 - Use to set decode lengths (default - 0). See Decode Lengths on page 58 for more information.
- Length2 - Use to set decode lengths (default - 14). See Decode Lengths on page 58 for more information.
- Redundancy - Sets the reader to read the bar code twice before accepting data. A check in the checkbox
indicates that redundancy is enabled (default - enabled).
• Code 11
- Length1 - Use to set decode lengths (default - 4). See Decode Lengths on page 58 for more information.
- Length2 - Use to set decode lengths (default - 55). See Decode Lengths on page 58 for more information.
- Redundancy - Sets the reader to read the bar code twice before accepting data. A check in the checkbox
indicates that redundancy is enabled (default - enabled).
- Verify Check Digit - Check the integrity of all Code 11 symbols to verify that the data complies with the
specified check digit algorithm. This selects the check digit mechanism for the decoded Code 11 bar code.
+ No Check Digit - Do not verify check digit.
+ 1 Check Digit - Bar code contains one check digit (default).
+ 2 Check Digits - Bar code contains two check digits.
- Report Check Digit - Transmit Code 11 data with or without the check digit. A check in the checkbox
indicates to send Code 11 data with check digit (default - disabled).
• Matrix 2 of 5
- Length1 - Use to set decode lengths (default - 10). See Decode Lengths on page 58 for more information.
- Length2 - Use to set decode lengths (default - 0). See Decode Lengths on page 58 for more information.
- Redundancy - Sets the reader to read the bar code twice before accepting data. A check in the checkbox
indicates that redundancy is enabled (default - disabled).
- Report Check Digit - Transmit Matrix 2 of 5 data with or without the check digit. A check in the checkbox
indicates to send Matrix 2 of 5 data with check digit (default - enabled).
- Verify Check Digit - Enable this feature to check the integrity of all Matrix 2 of 5 symbols to verify that the
data complies with a specified check digit algorithm (default - enabled).
• UPCE1
DataWedge Configuration | 57
MN000017A01 | October 2013 | Send Feedback

Motorola TC55 Specifications

General

Brand	Motorola
Model	TC55
Category	Handhelds
Language	English