Need help?Do you have a question about the Omnicomm Profi and is the answer not in the manual?
General| Brand | Omnicomm |
|---|---|
| Model | Profi |
| Category | Touch terminals |
| Language | English |
Instructions for inserting a SIM card into the terminal.
Steps for inserting a second SIM and SD card into Optim terminals.
Procedure for placing the protective insert in Optim terminals.
Details pin assignments for Profi, Profi Wi-Fi, Optim, and Smart terminals' connectors.
Wiring diagrams for power supply and ignition key connections.
Guidelines for installing the terminal in a vehicle.
Provides mounting dimensions for Optim and Smart terminals.
Recommendations for antenna installation site and procedure.
Guide to configuring terminals using the Omnicomm Configurator software.
Lists parameters configurable via Omnicomm Configurator in advanced mode.
How to connect and use the Remote Configuration Server for terminal configuration.
Details GPRS setup for Optim, Profi, and Profi Wi-Fi terminals.
Configuration of Wi-Fi data transmission for Profi Wi-Fi terminals.
Setting up connections to Omnicomm and EGTS communication servers.
Parameters for configuring data collection from modules and external devices.
Settings for data transmission intervals and GSM/SMS parameters.
How to select the data source for ignition on/off registration.
Selecting the data source for vehicle speed (GPS, CAN bus, UI6).
Configuring engine RPM input for tachometers or CAN bus.
Configuration for accelerometer usage and calibration.
Control of dangerous driving based on speed, RPM, and acceleration.
Settings for detecting and reporting case tampering attempts.
Information about the internal battery's function.
Configuration for detecting and reporting GPS/GLONASS signal jamming.
Configuration for detecting and reporting GSM signal jamming.
How to restart the terminal through the service menu.
How to set or change the configuration password.
How to block or unblock data acquisition and transmission.
How to set passwords for terminal modification via RCS.
How the terminal SIM card number is displayed in RCS.
Connecting auxiliary equipment via RS-485 and RS-232 interfaces.
Details on specific interface settings like CAN-Log, J1708, NMEA.
Details on specific interface settings like Tachograph VDO and data transmission frequency.
Details on specific interface settings for TPMS and Truck-TPMS.
Connecting and configuring fuel level sensors.
Connecting Omnicomm LLS-AF sensors to Profi and Optim/Smart terminals.
Configuration settings for the Omnicomm ICON display.
Configuring engine hours calculation based on RPM values.
Settings for displaying data on the Omnicomm LLD indicator.
Connecting and configuring the Continental tachograph.
Using universal inputs for connecting various sensors and equipment.
Configuring sensors with pulse output for universal inputs.
Configuring sensors with potential output for universal inputs.
Configuring sensors with analog output for universal inputs.
Configuring sensors with frequency output for universal inputs.
Settings for driver identification using iButton keys or Omnicomm ICON display.
Configuration of authorized keys and output activation for driver identification.
Connecting and configuring temperature sensors via 1-Wire interface.
Connecting the voice communication set for terminals.
Connecting swipe card readout devices via 1-Wire interface.
Setting up rules for controlling external equipment via terminal outputs.
Configuring rule priority, events, states, and output operation modes.
Setting up geofences to enable controlled outputs based on location.
Settings for panic button functionality and GSM call button.
Connecting to the vehicle CAN bus for data acquisition.
Configuring CAN bus parameters and adding custom parameters.
Technical specifications for communication and power source.
Technical specifications for memory, I/O, and interfaces.
Technical specifications for USB, voice, accelerometer, design, and sensor connections.
LED indicators for communication status and power/ignition states.
LED indicators for GPS, GSM status, and module errors.
Sound notifications for Wi-Fi connection and data transmission.
Message formats for panic button triggers and dangerous driving events.
Message format for accident detection events.
Message formats for universal input triggering and body tampering.
SMS commands for siren control.
SMS commands for controlling digital outputs and taking pictures.
SMS commands for getting terminal state and connection status.
SMS commands for connecting to configurator server and setting APN.
SMS commands for GPS cold start and unblocking the terminal.
To Next Page
