Omron E5AN-H

346
Index
AT calculated gain, 248
AT execute/cancel
, 192
AT hysteresis
, 248
auto/manual select addition, 256
auto/manual switch
, 178
automatic cooling coefficient adjustment
, 271
automatic display return time, 250
auxiliary output * open in alarm
, 245
auxiliary output 1 assignment
, 263
auxiliary output 2 assignment, 264
auxiliary output 3 assignment
, 265
bank (0 to 7) PID set No.
, 210
bank (0 to 7) SP, 210
bank * alarm value 1
, 211
bank * alarm value 2
, 212
bank * alarm value 3, 213
bank * alarm value lower limit 1
, 212
bank * alarm value lower limit 2
, 213
bank * alarm value lower limit 3, 214
bank * alarm value upper limit 1
, 212
bank * alarm value upper limit 2
, 213
bank * alarm value upper limit 3, 214
bank 0 to 7 SP ramp set value
, 211
bank No.
, 179
bank numbers used, 237
bank soak time
, 215
bank wait band
, 215
character select
, 265
closed/floating, 239
cold junction compensation method
, 252
communications baud rate
, 281
communications data length
, 281
communications parity
, 281
communications stop bits
, 281
communications Unit No.
, 281
communications writing
, 193
control output 1 assignment
, 261
control output 1 ON/OFF count alarm set value, 279
control output 1 ON/OFF count monitor
, 278
control output 2 assignment
, 262
control output 2 ON/OFF count alarm set value, 279
control output 2 ON/OFF count monitor
, 278
control period (cooling)
, 230
control period (heating), 230
cooling coefficient
, 201
dead band
, 201
decimal point
, 226
derivative time
, 200
direct setting of position proportional MV
, 270
direct/reverse operation, 231
display bank selection
, 210
display PID selection
, 216
display refresh period
, 277
event input assignment *
, 238
extraction of square root enable
, 240
extraction of square root low-cut point, 207
HB ON/OFF
, 246
heater burnout detection 1
, 194
heater burnout detection 2, 196
heater burnout hysteresis
, 247
heater burnout latch
, 246
heater current 1 value monitor, 181, 194
heater current 2 value monitor
, 182, 195
heater overcurrent detection 1
, 195
heater overcurrent detection 2, 196
heater overcurrent hysteresis
, 273
heater overcurrent latch
, 272
heater overcurrent use, 272
HS alarm 1
, 197
HS alarm 2
, 198
HS alarm hysteresis, 258
HS alarm latch
, 258
HS alarm use
, 257
hysteresis (cooling), 202
hysteresis (heating)
, 202
infrared communications use
, 193
initial setting/communications protect, 172
input digital filter
, 249
input error output
, 251
input shift type
, 256
input type, 224
integral time
, 200
LBA band
, 260
LBA detection time
, 259
LBA level
, 259
leakage current 1 monitor
, 183, 197
leakage current 2 monitor
, 183, 198
limit cycle MV amplitude
, 248
linear current output
, 236
lower-limit temperature input shift value, 199
manual MV limit enable
, 270
manual reset value
, 202
MB command logic switching, 252
monitor/setting item
, 274
monitor/setting item display 1 to 5
, 220
motor calibration, 240
move to advanced function setting level
, 241
move to calibration level
, 280
move to protect level
, 172
move to protect level time
, 251
MV at PV error
, 204
MV at stop, 204
MV at stop and error addition
, 256
MV change rate limit
, 206