Panasonic PT-REQ15 - Page 167

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 167
f When [AUTOMATIC SWITCHING] is set to [ENABLE], and [BACKUP INPUT STATUS] shows [ACTIVE], the signal is switched to the
backup input if a disruption occurs in the input signal.
f When [AUTOMATIC SWITCHING] is set to [ENABLE], the indication in [BACKUP INPUT STATUS] will change to [INACTIVE] if the input
signal is disrupted and automatically switched to the backup input. In this case, it is not possible to switch to the backup input signal until the
original input signal is restored. If the input has switched to the backup input automatically, it is possible to switch to the backup input signal
when the original signal has has been restored. In this case, the current input is maintained.
f The primary input setting values are applied to image adjustment values such as the [PICTURE] menu → [PICTURE MODE], [GAMMA],
and [COLOR TEMPERATURE].
[SECONDARY INPUT]
Set the secondary input switching function that will automatically switch to the specied input when the input
signal of projecting image is discontinued.
1) Press as to select [NO SIGNAL SETTING].
2) Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3) Press as to select [SECONDARY INPUT].
4) Press the <ENTER> button.
f The [SECONDARY INPUT] screen is displayed.
5) Press as to select the input to be specified as the switching destination, and press the <ENTER>
button.
[OFF]
Disables the secondary input switching function.
[HDMI1]
Sets the secondary input to HDMI1.
[HDMI2]
Sets the secondary input to HDMI2.
[DisplayPort]
Sets the secondary input to DisplayPort.
[SDI [SLOT]]
*1
Sets the secondary input to SDI.
[SDI OPT1 [SLOT]]
*2
Sets the secondary input to SDI OPT1.
[SDI OPT2 [SLOT]]
*2
Sets the secondary input to SDI OPT2.
[DIGITAL LINK [SLOT]]
*3
Sets the secondary input to DIGITAL LINK
*4
.
[PressIT [SLOT]]
*5
Sets the secondary input to PressIT.
[SLOT]
*6
Sets the secondary input to SLOT.
*1 This item can be selected when the optional 12G-SDI Terminal Board (Model No.: TY-SB01QS) is installed in <SLOT>.
*2 This item can be selected when the optional Function Board for 12G-SDI Optical (Model No.: TY-SB01FB) is installed in <SLOT>.
*3 This item can be selected when the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) is installed in <SLOT>.
*4 Individual input on the twisted‑pair‑cable transmitter or the DIGITAL LINK output supported device cannot be specied.
*5 This item can be selected when the optional Wireless Presentation System Receiver Board (Model No.: TY-SB01WP) is installed in <SLOT>.
*6 This item can be selected when the Function Board by other manufacturers is installed in <SLOT>.
Note
f When the [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE] is set to
anything other than [OFF], the secondary input switching function will not operate even when [SECONDARY INPUT] is set to anything other
than [OFF]. The backup input switching function is prioritized.
[BACK COLOR]
Set the display of the screen when a signal is not input.
1) Press as to select [NO SIGNAL SETTING].
2) Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3) Press as to select [BACK COLOR].
4) Press the <ENTER> button.
f The [BACK COLOR] screen is displayed.
5) Press as to select the item.
f Select the image you want to display.
[BLUE]
Displays blue in the entire projection screen.
[BLACK]
Displays black in the entire projection screen.