Panasonic PT-REQ15 - [Status]

Chapter 4 Settings — [PROJECTOR SETUP] menu
178 - ENGLISH
[LENS MEMORY LOAD]
Loads the registered lens memory. (x page 150)
[PROJECTION METHOD]
Switches the [PROJECTION METHOD] setting. (x page 148)
[GEOMETRY]
Switches the [GEOMETRY] setting. (x page 107)
[ANGLE MONITOR]
Displays the [ANGLE MONITOR] screen. (x page 181)
[SCREEN MARKER]
Switches the [SCREEN MARKER] setting. (x page 122)
4) Press the <ENTER> button.
Note
f The [FUNCTION BUTTON] screen can also be displayed by holding down the <FUNCTION> button on the remote control.
[STATUS]
Display the status of the projector.
1) Press as to select [STATUS].
2) Press the <ENTER> button.
f The [STATUS] screen is displayed.
3) Press qw to switch the pages.
f The page will change each time you press the button.
[PROJECTOR TYPE]
Displays the type of the projector.
[SERIAL NUMBER]
Displays the serial number of the projector.
[PROJECTOR RUNTIME]
Displays the runtime of the projector.
[LIGHT RUNTIME]
Displays the runtime of the light source 1 and the light source 2.
[CONTINUOUS LIGHTING
TIME]
Displays the elapsed time from when the light source is illuminated.
The elapsed time after the illumination of the light source can be conrmed when adjusting the focus.
The elapsed time is reset when the light source is temporarily turned o󰀨 such as using the shutter
function.
[FIRMWARE VERSION]
Displays the rmware version of the projector.
[INTAKE AIR TEMP.]
*1
Displays the intake air temperature status.
[EXHAUST AIR TEMP.]
*1
Displays the exhaust air temperature status.
[SELF TEST]
Displays the self-diagnosis information.
[INPUT]
Displays the input terminal currently selected.
Displays the representative input terminal when one image is displayed with multiple input signals.
[SIGNAL NAME]
Displays the input signal name.
[MEMORY NO.]
*2
Displays the memory number of the input signal.
[BACKUP INPUT STATUS]
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 123)
[NUMBER OF REGISTERED
SIGNAL]
*2
Displays the number of registered signals.
[COOLING CONDITION]
Displays the set cooling conditions.
[ATMOSPHERIC PRESSURE]
Displays the atmospheric pressure.
[REMOTE2 STATUS]
Displays the control status of the REMOTE2.
[AC VOLTAGE]
Displays the input supply voltage.
[LENS] [LENS TYPE]
Displays the projection lens type.
[ON COUNT] [POWER ON TIMES]
Displays the number of times the power is turned on.
[UPGRADE KIT] [ET-NUK10]
Displays the activation status by the NFC Upgrade Kit (Model No.:
ET-NUK10).
Or, displays the status of the NFC function.
[ACTIVATED]: The NFC function can be used.
[NOT ACTIVATED]: The NFC function cannot be used.
[SLOT]
Displays the product model number of the Function Board installed in <SLOT>.
Also, the rmware version is displayed after the product model number.
[OPERATING MODE]
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
[NORMAL]
Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
[ECO]
Displays the runtime of the light source with [OPERATING MODE] set to [ECO].
[QUIET]
Displays the runtime of the light source with [OPERATING MODE] set to [QUIET].
[USER1]
Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
[USER2]
Displays the runtime of the light source with [OPERATING MODE] set to [USER2].