Chapter 4 Settings — [ADVANCED MENU] menu
130 - ENGLISH
f Pressing the <MENU> button twice allows to reselect the items for [BLACK BORDER AREA].
30) Press as to select [BLACK BORDER LEVEL].
31) Press the <ENTER> button.
f The adjustment area in the projected image becomes temporarily bright and the [BLACK BORDER
LEVEL] screen is displayed.
f [RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].
32) Press as to select an item, and press qw to adjust the setting.
f Once the adjustment is completed, press the <MENU> button to return to the [BLACK LEVEL ADJUST]
screen.
33) Press as to select [UPPER], [LOWER], [LEFT], or [RIGHT] for [OVERLAPPED BLACK LEVEL].
34) Press the <ENTER> button.
f The adjustment area in the projected image becomes temporarily bright and the [OVERLAPPED BLACK
LEVEL] screen is displayed.
f [RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].
35) Press as to select an item, and press qw to adjust the setting.
[BLACK BORDER AREA] (Right)
Projection range Edge blending [WIDTH] (Right)
[MARKER] (Red)
Edge blending [START] (Right)
([MARKER] (Green))
[BLACK BORDER LEVEL]
[OVERLAPPED BLACK LEVEL] (Right)
[NON-OVERLAPPED BLACK LEVEL]
Note
f It is recommended to select [GEOMETRY UNLINKED] when using the projector in following conditions.
g Project an image to a at screen.
g Combine projected images from multiple projectors in vertical column or horizontal row.
f [BLACK LEVEL ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difcult to
notice when [EDGE BLENDING] is used to structure a multi-display screen. The optimal point of correction is set by adjusting [NON-
OVERLAPPED BLACK LEVEL] so that the black level of the overlapping image area will be the same level as the non-overlapping area. If
the border area of the part where the image is overlapping and the non-overlapping part gets brighter after adjusting [NON-OVERLAPPED
BLACK LEVEL], adjust the width or the shape of the top, bottom, left, or right. Adjust [BLACK BORDER LEVEL] when the adjustment makes
only the border area darker.
f The joining part may look discontinuous depending on the position you are looking from when a screen with high gain or rear screen is used.
f When conguring multiple screens using both horizontal and vertical edge blending, adjust [OVERLAPPED BLACK LEVEL] rst before
making adjustments in Step 16). Adjustment method is same as the procedure of [NON-OVERLAPPED BLACK LEVEL].
f If only horizontal or vertical edge blending is used, set all items in [OVERLAPPED BLACK LEVEL] to 0.
f The [AUTO TESTPATTERN] setting will change in conjunction with the setting in the [DISPLAY OPTION] menu → [COLOR MATCHING] →
[AUTO TESTPATTERN].
f Adjustment of the shape of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK BORDER LEVEL] is a function to
perform the edge blending together with the adjustment of [GEOMETRY] (x page 120). If [NON-OVERLAPPED BLACK LEVEL] is
deformed by correcting the distortion of the projected image with [GEOMETRY], perform the adjustment following Step 21) to Step 29), and
adjust the edge blending according to the shape of [NON-OVERLAPPED BLACK LEVEL].
f An error is accumulated by repeatedly adjusting the position of the adjustment points, which may distort the shape of the border awkwardly.
In such a case, initialize the shape of the border. Initializing the shape of the border will reset the shape to the factory default (unadjusted
state). For details, refer to “Initializing the shape of the border” (x page 130).
Initializing the shape of the border
Initialize the data adjusted with [UPPER FREE SHAPE], [LOWER FREE SHAPE], [LEFT FREE SHAPE], and
[RIGHT FREE SHAPE] and restore to the factory default settings (unadjusted state).
1) Press as to select [EDGE BLENDING].
2) Press qw to select [ON] or [USER].
To Next Page
Loading...
